« previous next »
Pages: [1]   Go Down

Author Topic: Need to find unit on Streamline unit 48 port  (Read 2930 times)

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Need to find unit on Streamline unit 48 port
« on: April 28, 2015, 04:55:52 PM »
I have a cable that has been cut and pulled out and not able to trace back the the main phone room and i need to figure out what port the phone was set up on.  This is was i found in the maint command line and i'm figuring that 1-3-1-48 is the port number, but if i pull the cross connect on a known working phone on port 1-3-1-51 it still shows as IDLE. I'm looking at the 110 blocks and i figure that there are 24 ports to each 25 pair cable and 1-3-1-48 would be the last one on the second cable.  Am i right in thinking that ????

 Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  48  1| 5330e IP             |Out of Service |         |      |         
 1 3  1  48  2| Unassigned           |Not applicable |         |      |         
 1 3  1  48  2| Alternate Codec      |Out of Service |         |      |         
----------------------------------------------------------------------------   
  Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  51  1| 5330e IP             |Idle           |         |      |         
 1 3  1  51  2| Unassigned           |Not applicable |         |      |         
 1 3  1  51  2| Alternate Codec      |Idle           |         |      |         
----------------------------------------------------------------------------   
Logged

Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #1 on: April 28, 2015, 05:00:22 PM »
"1 3  1  48  1" is a PLID.   It is not a cross connect.

You won't be able to find the wire from the 3300.

I suspect that the easiest way to ID what cable it may be on is to check which lights are inactive on the streamline and go from there.


Ralph
Logged

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #2 on: April 28, 2015, 05:05:34 PM »
Problem is there are no indicators or light on the unit to show any activity.
Logged

Offline lowradiation

  • Full Member
  • ***
  • Posts: 127
  • Karma: +4/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #3 on: April 29, 2015, 04:37:58 PM »
Log into the streamline's web interface.  It will show activity of the ports
Logged

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #4 on: April 30, 2015, 12:48:22 PM »
Does anybody know if there is a default login and password for the Streamline unit ???
Logged

Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2201
  • Country: us
  • Karma: +66/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #5 on: April 30, 2015, 01:35:03 PM »
Default login is “admin” password is “admin” (without quotes)
Logged

Pages: [1]   Go Up
« previous next »
 

Sitemap 1 2 3 4 5 6 7 8 9 10