Author Topic: Need to find unit on Streamline unit 48 port  (Read 2935 times)

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Need to find unit on Streamline unit 48 port
« on: April 28, 2015, 04:55:52 PM »
I have a cable that has been cut and pulled out and not able to trace back the the main phone room and i need to figure out what port the phone was set up on.  This is was i found in the maint command line and i'm figuring that 1-3-1-48 is the port number, but if i pull the cross connect on a known working phone on port 1-3-1-51 it still shows as IDLE. I'm looking at the 110 blocks and i figure that there are 24 ports to each 25 pair cable and 1-3-1-48 would be the last one on the second cable.  Am i right in thinking that ????

 Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  48  1| 5330e IP             |Out of Service |         |      |         
 1 3  1  48  2| Unassigned           |Not applicable |         |      |         
 1 3  1  48  2| Alternate Codec      |Out of Service |         |      |         
----------------------------------------------------------------------------   
  Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  51  1| 5330e IP             |Idle           |         |      |         
 1 3  1  51  2| Unassigned           |Not applicable |         |      |         
 1 3  1  51  2| Alternate Codec      |Idle           |         |      |         
----------------------------------------------------------------------------   


Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #1 on: April 28, 2015, 05:00:22 PM »
"1 3  1  48  1" is a PLID.   It is not a cross connect.

You won't be able to find the wire from the 3300.

I suspect that the easiest way to ID what cable it may be on is to check which lights are inactive on the streamline and go from there.


Ralph

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #2 on: April 28, 2015, 05:05:34 PM »
Problem is there are no indicators or light on the unit to show any activity.

Offline lowradiation

  • Full Member
  • ***
  • Posts: 127
  • Karma: +4/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #3 on: April 29, 2015, 04:37:58 PM »
Log into the streamline's web interface.  It will show activity of the ports

Offline mickyspring

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #4 on: April 30, 2015, 12:48:22 PM »
Does anybody know if there is a default login and password for the Streamline unit ???

Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2202
  • Country: us
  • Karma: +66/-0
    • View Profile
Re: Need to find unit on Streamline unit 48 port
« Reply #5 on: April 30, 2015, 01:35:03 PM »
Default login is “admin” password is “admin” (without quotes)


 

Sitemap 1 2 3 4 5 6 7 8 9 10