Author Topic: 3300 embedded analog- no dial tone  (Read 4842 times)

Offline PC77375

  • Full Member
  • ***
  • Posts: 191
  • Country: us
  • Karma: +6/-0
    • View Profile
3300 embedded analog- no dial tone
« on: October 30, 2013, 02:44:18 PM »
Having issues with an embedded analog not presenting dial tone on a 3300 installed in India. I am able to call the extension and when I do "State PLID" while calling, it shows status as ringing.
A local vendor already replaced the analog card and the controller. I spoke with them about a possible programming error and they advised that they have verified all programming as correct. Anyone have any suggestions?


Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #1 on: October 30, 2013, 03:30:18 PM »
I don't think there is anything in programming that you can set (except maybe "non-busy" extension option) that would stop an analog port from presenting DT.   If the AMB has been replaced then you may have a bad controller.

Ralph

Offline PC77375

  • Full Member
  • ***
  • Posts: 191
  • Country: us
  • Karma: +6/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #2 on: October 30, 2013, 03:34:57 PM »
Controller was already replaced. How crazy would it be if the second one was DOA as well?

Offline jrg0852

  • Sr. Member
  • ****
  • Posts: 309
  • Country: us
  • Karma: +3/-0
  • Look out for the next tech. because it may be you!
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #3 on: October 30, 2013, 03:50:10 PM »
My thoughts:

The ribbon cable was reseated from the AMB to the mother board, right?

You tested directly in back of the system with butt set?

Is this LS or ONS (in or out)?

Thanks.

Offline x-man

  • Hero Member
  • *****
  • Posts: 1129
  • Country: gb
  • Karma: +25/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #4 on: October 31, 2013, 06:37:41 AM »
Every time we have had this its been a defective AMB (just once it was the ribbon cable that was not seating properly but we jiggled it around and got it to work) although once it was us being stupid and plugging into LS ports rather than ONS ports.

Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #5 on: October 31, 2013, 07:20:44 AM »
although once it was us being stupid and plugging into LS ports rather than ONS ports.

Yeah, that happens some times.

Offline PC77375

  • Full Member
  • ***
  • Posts: 191
  • Country: us
  • Karma: +6/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #6 on: October 31, 2013, 09:30:36 AM »
Tried onsp 1 and onsp 2, also with an analog phone connected directly to the ports. Do you think it could be something that needs to be changed in the circuit descriptor that would be specific to analog devices in India?

Offline matthew

  • Full Member
  • ***
  • Posts: 123
  • Country: au
  • Karma: +2/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #7 on: October 31, 2013, 09:51:03 PM »
Got the right country selected in License and Option Selection?

Also, we had a faulty analog extn problem that drove us crazy - could ring it, but couldn't make calls and only had a no progress tone instead of dial tone. Turned out to be a faulty DSP card.
« Last Edit: October 31, 2013, 09:54:28 PM by matthew »

Offline LoopyLou

  • Hero Member
  • *****
  • Posts: 556
  • Country: ca
  • Karma: +7/-0
    • View Profile
Re: 3300 embedded analog- no dial tone
« Reply #8 on: November 04, 2013, 08:06:25 AM »
What needs to happen on a trunk to orginate a call in India? As already suggested would need the correct country code programmed. Not a ground start trunk by any chance?


 

Sitemap 1 2 3 4 5 6 7 8 9 10