Messages

1

Mitel SX200, SX2000, and older SX platforms / Re: SX-200 MX ARS

« on: October 18, 2018, 05:43:23 PM »

Thank you for the fast reply.
I think you put me on the right track.
Cheers!

2

Mitel SX200, SX2000, and older SX platforms / SX-200 MX ARS

« on: October 18, 2018, 05:14:38 PM »

 
Stuck on ARS issue.
Hotel account wants to keep some in-house extensions from dialing extensions starting with 4,5, 6  and restrict outgoing on 9,but allow other digits like 911, 0 and exts. starting with 1, 2, 3, 4 etc.

Have not done ARS on 200 in a long time.  Any suggestions?
Thanks

3

Mitel Jobs and Mitel Careers / Re: Looking for Mitel 3300/MVB Technician

« on: August 06, 2018, 03:34:55 PM »

Are you still available?

4

Mitel Jobs and Mitel Careers / Re: Mitel Remote tech available

« on: August 06, 2018, 03:33:11 PM »

We would be interested in your remote support.

5

MiVoice Office 250/Mitel 5000 / Re: Mitel 5000 LS ports

« on: February 08, 2018, 11:37:48 AM »

Thanks guys, I believe that is the problem, just frustrated with Telco.
Have to bite the bullet on this one.

6

MiVoice Office 250/Mitel 5000 / Mitel 5000 LS ports

« on: February 07, 2018, 07:08:42 PM »

Have a 5000 6.2 with 20 analog lines, everything is fine except for 1 line that has burned out port 1 of the onboard 
LS ports twice!
Had Frontier check the line for excess voltage and they say the line is within specs.
Have gone through 2 processor modules since I have no other available ports to use. (Customer won't go to T-1)
If a call comes in there is a loud squeal on the line.
Anyone seen this, or know what is going on?

7

Mitel SX200, SX2000, and older SX platforms / Re: SX-200 AX

« on: September 07, 2017, 04:03:57 PM »

It's all good, got it going.
Thanks again.

8

Mitel SX200, SX2000, and older SX platforms / Re: SX-200 AX

« on: September 07, 2017, 01:37:17 PM »

I will try to reburn the software on the CF and let you know what happens.
Appreciate your input.

9

Mitel SX200, SX2000, and older SX platforms / Re: SX-200 AX

« on: September 07, 2017, 01:31:55 PM »

Thank you Ace.
I moved the CF to slot 2 and now it says can't load boot file.

10

Mitel SX200, SX2000, and older SX platforms / SX-200 AX

« on: September 07, 2017, 12:24:06 PM »

Just got an SX-200 AX and it does not get past auto-boot.
The parameters look correct and I tried to follow the THB, but no luck.
I installed the 4gig CF in Slot 1 and there in nothing in slot 2
What am I missing?

11

Mitel Jobs and Mitel Careers / Looking for Mitel 3300/MVB Technician

« on: August 16, 2017, 05:59:30 PM »

Fast growing Mitel dealer in So. California looking for experienced technician to install and service Mitel MiVoice Business, MiCollab, MICC, NuPoint and call recording on a subcontract or on staff basis. Remote support and programming also will be considered.

12

Mitel Jobs and Mitel Careers / Re: Looking for a Remote Only tech position

« on: August 16, 2017, 05:40:50 PM »

Are you still available?

13

Mitel MiVoice Business/MCD/3300 / Re: Handset volume

« on: August 04, 2016, 03:59:41 PM »

It is not saving regardless of the new setting.

14

Mitel MiVoice Business/MCD/3300 / Handset volume

« on: August 04, 2016, 03:42:41 PM »

I have a customer with MiVoice Business 7.1. 

We set the handset volume saved to YES in all IP phones COS.

It still reverts back to the default setting of 3 when hung up.

Two questions:
1) How do I increase the default from 3 to 5? Don't see it in System Options.
2) Do the phones need to be rebooted for the new setting to take hold? I have seen conflicting posts about that.

TIA