Author Topic: How to change a Mitel 3300 to an Expanded Controller  (Read 5357 times)

Offline TimPNRHA

  • Jr. Member
  • **
  • Posts: 47
  • Karma: +0/-0
    • View Profile
How to change a Mitel 3300 to an Expanded Controller
« on: June 06, 2014, 01:58:55 PM »
Good Day,

I just have a quick question, currently I have quite a few Mitel 3300 Enterprise controllers that I am standardizing that all controllers must be expanded. Is it okay to get MXE III hardware to put into to an MXE II, this are the parts that I was given from our reseller, as well what is the best way to expand the controller, is it matter of just putting the hardware in and the secondary controller will just begin to copy the current config files?

MXe AC Power supply--$405.00--Product code--50005084
MXe III Raid Sub system--$1,620.00--Product code--50006431
3300 160G SATA hdd 2 pack--$300.00--Product code--50006489
3300 MXe III Expansion Kit--$1,824.12--Product code--52002581

Thank you,


Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #1 on: June 06, 2014, 07:19:32 PM »
No, the MXe III hardware will be different.


Sent from my iPhone using Tapatalk

Offline lundah

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1210
  • Country: us
  • Karma: +66/-0
  • Senior Chief Grunt
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #2 on: June 09, 2014, 09:20:50 AM »
MXE-II and MXE-III hardware component are not compatible with each other. Different bus speeds and drive interfaces.

Offline marcolive

  • Full Member
  • ***
  • Posts: 131
  • Karma: +2/-0
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #3 on: June 09, 2014, 11:01:01 PM »
I think the only compatible part would be the power supply

Offline LoopyLou

  • Hero Member
  • *****
  • Posts: 556
  • Country: ca
  • Karma: +7/-0
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #4 on: June 10, 2014, 08:29:29 AM »
To make a system expanded you are going from the base 64 E2T channels and 64 echo cancellors to 128 of each. All you need to do is buy the proper expansion kit to truly go "expanded". You can add a second power supply and second hard drive on the base system. As suggested you have the right components listed but might need to make sure the ones being ordered are compatible with older controllers. The expanded kit is composed of two cards ( Processor card and echo cancellor card ).

IF you check the tech handbook under the FRU section you will see the MXe II and MXE III do have different part numbers for the RAID card and processor card. 


Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2201
  • Country: us
  • Karma: +66/-0
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #5 on: June 10, 2014, 09:33:21 AM »
I would add that the older raid card is discontinued

Offline lundah

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1210
  • Country: us
  • Karma: +66/-0
  • Senior Chief Grunt
    • View Profile
Re: How to change a Mitel 3300 to an Expanded Controller
« Reply #6 on: June 10, 2014, 09:51:43 AM »
I would add that the older raid card is discontinued

So is the expansion processor.


 

Sitemap 1 2 3 4 5 6 7 8 9 10