« previous next »
Pages: [1]   Go Down

Author Topic: UC 360 dropping calls  (Read 4223 times)

Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
UC 360 dropping calls
« on: July 30, 2013, 10:15:17 PM »
MCD 6.0 SP1

User reported UC 360 dropped call after some time on a conference call. I have very few details and hope to have more in the morning. They said it was after more than 15 min, but not sure how long the call was before it dropped. I am not using any call duration on this site.

Are there any timers in the SIP profile that may cause this?

I didn't see any logs that would point to any quality issues.
Logged

Offline marcolive

  • Full Member
  • ***
  • Posts: 131
  • Karma: +2/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #1 on: July 30, 2013, 10:48:28 PM »
Double check that Session Timer is at 0 in SIP Device Capabilities. That the only thing documentation says about timers for UC360.
Logged

Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #2 on: July 31, 2013, 07:29:36 AM »
Session timer is already at 0. I hope to recreate this problem today, maybe that will help. Of course, it will work just fine while I am on site and screw up again tomorrow morning.
Logged

Offline martyn

  • Hero Member
  • *****
  • Posts: 688
  • Country: au
  • Karma: +10/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #3 on: July 31, 2013, 07:36:35 AM »
Is the device configured as a sip endpoint or uc360? Does it have the default sip device capabilities that are created for a 360 at mcd 6?
Logged

Offline marcolive

  • Full Member
  • ***
  • Posts: 131
  • Karma: +2/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #4 on: July 31, 2013, 07:38:27 AM »
My error. Session Timer should be at 3600! Sorry for that!

I think very firsts versions of UC360 used 0.
Logged

Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #5 on: July 31, 2013, 07:39:16 AM »
UC Endpoint and no, I created a SIP device capabilities entry using the UC 360 admin guide. What is the preconfigured number I can use? I'll try 3600 and see what happens.
Logged

Offline martyn

  • Hero Member
  • *****
  • Posts: 688
  • Country: au
  • Karma: +10/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #6 on: July 31, 2013, 07:29:18 PM »
SIP Device capability 71 is the pre-created one. Like you I followed the guide the first time I did it and then realised that there is a pre-configured one, but they don't tell you that in the config guide  :)

That has the session timer as 0 rather than 3600 in it as well.
« Last Edit: July 31, 2013, 07:30:50 PM by martyn »
Logged

Offline Mattmayn

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1069
  • Country: vi
  • Karma: +14/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #7 on: July 31, 2013, 07:41:28 PM »
I went ahead and changed the session timer to 3600 and made an hour long call with my cell without incident today.

I thought that the admin guide on MOL said explicitly that 71 was not compatible with the UC360.
Logged

Offline irongladiator

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 346
  • Country: us
  • Karma: +13/-0
    • View Profile
Re: UC 360 dropping calls
« Reply #8 on: September 01, 2015, 05:13:19 PM »
Quote from: Mattmayn on July 31, 2013, 07:41:28 PM
I went ahead and changed the session timer to 3600 and made an hour long call with my cell without incident today.

I thought that the admin guide on MOL said explicitly that 71 was not compatible with the UC360.
Mattmayn,
An old post for sure. After your comment, I thought I'd share this. (See Below)



This was taken right out of the "Mitel UC360 Admin Guide R2.1 SP1".

 ;)

Thanks,
-Iron
Logged

Pages: [1]   Go Up
« previous next »
 

Sitemap 1 2 3 4 5 6 7 8 9 10