install with Mitel Mitel Communications Director Software Installer

[kengo]

Good morning everyone. I started the installation with the program. It lasted 17 hours (clean install), but in the end hung. checked what happened with putti. get a log like this:
[VxWorks Boot]: @

boot device          : ata=0,0
unit number          : 0
processor number     : 0
file name            : /partition1/RTC8260
inet on ethernet (e) : 192.168.1.2:ffffff00
gateway inet (g)     : 192.168.1.1
user (u)             : ftp
ftp password (pw)    : @
flags (f)            : 0x0
other (o)            : qefcc


Disk Configuration Started.
Creating block device for controller  0 drive 0... done.
Creating CBIO device for controller  0 drive 0... done.
0KB added to /partition1 partition
free disk space after partition 0 is 0KB
0KB added to /partition2 partition
free disk space after partition 1 is 0KB
0KB added to /partition3 partition
free disk space after partition 2 is 0KB
0KB added to /partition4 partition
free disk space after partition 3 is 0KB
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/partition1) on controller 0 drive 0... done.
Creating Cache Layer for partition 1 (/partition2) on controller 0 drive 0... done.
Creating Cache Layer for partition 2 (/partition3) on controller 0 drive 0... done.
Creating Cache Layer for partition 3 (/partition4) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/partition1) on controller 0 drive 0... done.
Creating Dos FS device for partition 1 (/partition2) on controller 0 drive 0... done.
Creating Dos FS device for partition 2 (/partition3) on controller 0 drive 0... done.
Creating Dos FS device for partition 3 (/partition4) on controller 0 drive 0... done.
Disk Configuration Complete.
Loading /partition1/RTC8260...n/a

Error loading file: errno = 0x380003.


MITEL SYSTEM ROM R3.1/11 Aug 10 2012

CCA Number                      : 56009216 RC.2
System Model                    : 00610001 F100
CPU Model                       : 8360 R80480021
Reset Config Low                : 08030008
Reset Config High               : b4500006
Coherent System Bus Clock (MHz) : 266
CPM Clock (MHz)                 : 266
Core Clock (MHz)                : 399
DDR Clock (MHz)                 : 133
Local Bus Clock (MHz)           : 66
Input Clock (MHz)               : 33
Internal Memory Map             : f0000000
Main Memory (MB)                : 512
Local Memory (MB)               : 0
Flash Memory (MB)               : 2
MAC Address                     : 08000f6004a8
L2 Switch                       : 0
POST Bypass                     : 0
Watchdog Bypass                 : 0
Slot Id                         : 0

Starting POST...

SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS1 Address  Walk 1................... PASSED
SDRAM CS1 Address  Walk 0................... PASSED

Starting vxWorks...

Reset Cause                     : 0x103 - SOFTWARE_RESET

VxWorks System Boot

Copyright 1984-2002  Wind River Systems, Inc.

CPU: Mitel Embedded PPC83XX F100
Version: VxWorks5.5.2
BSP version: 3.1/11
Creation date: Aug 10 2012, 10:47:30

Attempt to start the installation again, is not successful. It is possible to install a usb?

[acejavelin]

No, but a manual installation is pretty simple, the instructions are clearly laid out in the technicians handbook. No software installer needed, just the software on your laptop/PC with a serial port, an FTP server software (Filezilla works well), serial cable, and a terminal program (hyperterm or Teraterm).

[LoopyLou]

Basically it was not able to retrieve the software from you laptop.

[ralph]

Is your windows firewall turned on?

Ralph

[acejavelin]

Is your windows firewall turned on?

Ralph

^^ This... has bit me more than once, make sure the Windows Firewall is disabled, or any other firewall/security software such as McAffee, Norton, AVG, etc. or anything else that is providing firewall services. You can always test this easy enough from any PC on the network, open a CMD window or FTP client and try to FTP to your laptop with the credentials you have setup. I highly recommend using a third party FTP server over Windows FTP, such as FileZilla, the ability to watch things happening is very convenient (remember to disable the embedded FTP Server service in Windows!!!).

[ralph]

I highly recommend using a third party FTP server over Windows FTP, such as FileZilla, the ability to watch things happening is very convenient.

This has also bitten me.   We'd try to use Filezilla (great product btw) and I had my IIS FTP turned on.   FTP then tried to use IIS instead of Filezilla.   So... be sure IIS is turned off.

Ralph

[LoopyLou]

You can always test your FTP by using opening a cmd window in W7 and launching an FTP session to yourself and that should tell you that IIS is at least setup correctly. Then it almost always comes down to firewall issues.