definitive Shell command guide?

[cmac1]

Probably not the definative guide - but I do try and maintain a list of VX Works Commands on my website........

http://www.chris-mcandrew.co.uk

Look under Mitel and then VX Works (you will have to register to see the doc).

I appologise for the current lack of info on the site but I am just in the processs of rebuilding it.

hope that helps   :-)

[wobbly_head_bob]

-> vlan_off

This will reset the system IP VLAN setting back to default of 1.  For those times you fat finger something, then proceed to reboot....  then have to come in on a Saturday morning not being able to connect to the system.

[Chakara]

  Sweet - keep em coming!

-chak

[v2win]

you can also do a vlan_on to turn it back on

[limamikeseven]

HI all,
The best way of getting commands is by staying logged in to the console while you execute a maintenance command or issue a reset system or even doing an upgrade, all the commands or most of them are printed through the console.

Rgds

[ianbt001]

Gents with ref to the shell, I can ftp to the system and login but cannot remember how to then access the desktop etc, I am 2000 (including the SG, now that was a beast) trained and have been shown before but cannot remember, can someone pint me in right direction.

[Aelarth]

hey guys, thanks for all the commands so far, you've made my life much easier.

To access the desktop, connect the server lan port to your network card and make sure the network card is on the same subnet as the server. Open internet explorer and go to https://[IP address of Server]/main.htm (without [ ]). Download and install the certificate and you should be able to access the tools once you log in. If you still can't access the desktop tool, then your account is not configured for it. To configure it, go to the system administration tool, then users and devices -> user and device configuration, double-click on your directory name or number then go to Access and Authentication and check the desktop admin box.

I now have a question of my own. Does anyone know if it's possible to configure the layer 2 switch ip address through the RTC shell? I'm using the Mxe III version of the 3300ICP.

Thanks again.

Aelarth

[ralph]

ataShow (shell command) shows hard drive infomation

keywords: Mitel hard drive, Mitel hard disk

[marcolive]

Just in case some of you don't know that command :

vmPortStatusInfo in VxWorks shows the status of all EMEM ports. Useful to troubleshoot a defective port!

[ralph]

exeSysDbgCmds()

This command is executed from the RTC.
It runs a script that saves current system status then reboots the system.
This is very similar to holding the reset (or was it the alarm button) so when the system is restored you can grab the system diags.

Ralph

[acejavelin]

Not really a guide, but something that isn't working... For a SIP IVR vendor I am supposed to enable early DPNSS ISDN messages (or something like that) which after enabling "Supress Simulated CCM before ISDN progress" in COS of TDM trunks I am supposed to go to the shell and enter"

CCS Enable DPNSS Early

But in the case of one system, MCD 6.0, it is not enabling but coming back with an unknown keyword. Any ideas?

[petr.necas]

There is also "reboot" command for rebooting the 3300:

-> reboot

[ralph]

From the SX2000 interface:

How do I restart SMDR (Station Message Detail Recording) without rebooting the controller?
 
If you're verified that SMDR is enabled in System Options and in the Classes of Service, run the following SX2000 commands:
2 - Pcb kill prog logsysspl
3 - Pcb kill prog logsysrtr
4 - Pcb kill prog logsysbfm

[lundah]

mipsEnvShow - shows the properties of the L2/MIPS processor on the CX and MXe controllers
mips_reset - resets the L2/MIPS processor
period 900,mips_reset - resets the L2/MIPS every 900 seconds. This is useful if for some reason the L2/MIPS fails (I've had a run of several 50005090 vintage MXe's that do this after the controller loses power, only known fix is to replace the controller chassis). The period command could be used with other shell commands as well.

[pmhaynes]

Restart web server
http://www.phonesystemhelp.info/2013/11/19/mcd-web-server/
Restart voicemail (useful instead of rebooting)
http://www.phonesystemhelp.info/2013/11/19/start-the-embedded-voicemail/
Restart TFTP server
http://www.phonesystemhelp.info/2013/11/20/mitel-tftp-server/