Author Topic: My AX controller failed restoring to CX controller  (Read 2267 times)

Offline jchristman2002

  • Jr. Member
  • **
  • Posts: 46
  • Karma: +1/-0
    • View Profile
My AX controller failed restoring to CX controller
« on: June 22, 2022, 05:12:40 PM »
My AX controller has failed and I restored to a CX controller.  Most things are OK but I am getting alarms from the 4+12 card that was previously in the AX controller.  I cannot find where to delete this card as it does not show up under hardware module ASU or anywhere for that matter.  I do see analog ports showing up under user advanced analog but I cannot clear them there.  I also see trunks showing up under hardware>trunks>analog>analog trunks but caonot clear those either


Offline sunspark

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 986
  • Country: mx
  • Karma: +16/-1
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #1 on: June 22, 2022, 07:16:04 PM »
I think you need to send email to amcsupport to untag the arid

Offline jchristman2002

  • Jr. Member
  • **
  • Posts: 46
  • Karma: +1/-0
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #2 on: June 22, 2022, 07:20:34 PM »
I have deactivated and reactivated several times and even cleared the hardware ID.  I even switch the ARID on our test system.  I am not sure licensing is the issue on this one.

Offline sunspark

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 986
  • Country: mx
  • Karma: +16/-1
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #3 on: June 23, 2022, 12:32:06 PM »
it is not by making a clear hardware id that you will solve your problem.
send an email to amc support, they will remove a tag on your ARID because you must surely have licenses associated with your AX that you do not have in the CX

Offline billbry66

  • Full Member
  • ***
  • Posts: 93
  • Karma: +3/-0
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #4 on: June 24, 2022, 06:36:01 AM »
i think its upset because it had config thats tied to a card that doenst exist

long shot but have you tried a fresh backup ( of the CX) and then an immediate restore)

backup restores normally purge data thats not valid ( long shot because you have sort of done that already)

only other think i can think of is export the forms , clear database and import them again manually

Offline jchristman2002

  • Jr. Member
  • **
  • Posts: 46
  • Karma: +1/-0
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #5 on: June 24, 2022, 06:04:37 PM »
The CX controller is/was brand new with a brand new HD.

Offline billbry66

  • Full Member
  • ***
  • Posts: 93
  • Karma: +3/-0
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #6 on: June 25, 2022, 10:32:35 PM »
yes and am i correct in assuming that you have restored the AX backup to it but have some issues.
if so can you create a new cx backup and then restore it

Offline jchristman2002

  • Jr. Member
  • **
  • Posts: 46
  • Karma: +1/-0
    • View Profile
Re: My AX controller failed restoring to CX controller
« Reply #7 on: June 30, 2022, 06:40:08 PM »
I eventually gave up and just built the CX controller from scratch.  I got a few other issues I can't get figured out but I will make new posts for those.


 

Sitemap 1 2 3 4 5 6 7 8 9 10