Author Topic: Basic SPA8000 configuration to connect to MiVB with SIP Trunking  (Read 1671 times)

Offline celswood

  • Contributer
  • *
  • Posts: 9
  • Country: gb
  • Karma: +0/-0
    • View Profile
Hi all,

Picked up a customer with some legacy kit. Moved their PRI over to SIP and their Linksys SPA8000 fail to make a call outbound. From the CCS trace it shows the outbound call over the SIP UA leg with a CIM/CCM of 0 but doesn't show the outbound leg of the call over the SIP Trunking Peer, can see the device making the call using the correct trunk access digit.

Set up a SIP softphone using the same UA and can make calls outbound ok so I don't think its the MiVB (v9.0) configuration, had a look at the SPA8000 and there is tons of options, not sure where to start. If anyone has a basic config that I can start on would be greatly appreciated.

Also note that the SPA8000 is on the same subnet as the MBG which the SIP trunks terminate.


Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #1 on: May 01, 2020, 02:54:30 PM »
You will probably have to do a SIP trace to understand what's going on, but what does it say on the display when you try to make a call?


Ralph

Offline celswood

  • Contributer
  • *
  • Posts: 9
  • Country: gb
  • Karma: +0/-0
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #2 on: May 06, 2020, 09:54:41 AM »
Hi Ralph,

Ran a SIP trace from the MiVB, currently the SPA8000 is getting a 403 Forbidden from the MiVB with the following reason "399 x.x.x.x "29H Access Barred"", checked COS for PSTN Access over DPNSS and COR access over the route, no problems there. When I attach a SIP softphone using the same credentials I can make calls fine.

Thanks,

Craig

Offline NEPhoneGuy

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 218
  • Country: us
  • Karma: +5/-0
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #3 on: May 06, 2020, 04:59:29 PM »
Hi Ralph,

Ran a SIP trace from the MiVB, currently the SPA8000 is getting a 403 Forbidden from the MiVB with the following reason "399 x.x.x.x "29H Access Barred"", checked COS for PSTN Access over DPNSS and COR access over the route, no problems there. When I attach a SIP softphone using the same credentials I can make calls fine.

Thanks,

Craig

What is the SPA8000 sending out in the invite? Can you attach that?

Offline celswood

  • Contributer
  • *
  • Posts: 9
  • Country: gb
  • Karma: +0/-0
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #4 on: May 07, 2020, 09:25:45 AM »
Session Initiation Protocol (INVITE)
    Request-Line: INVITE sip:xxxxxxxxxx@x.x.x.xSIP/2.0
    Message Header
        Via: SIP/2.0/UDP x.x.x.x:5060;branch=z9hG4bK-c60f402a
        From: "1122" <sip:xxx@x.x.x.x>;tag=28b0ef2c58330edao1
        To: <sip:xxxxxxxxxx@x.x.x.x>
        Remote-Party-ID: "xxxx" <sip:xxxx@x.x.x.x>;screen=yes;party=calling
            [Expert Info (Note/Undecoded): Unrecognised SIP header (remote-party-id)]
                [Unrecognised SIP header (remote-party-id)]
                [Severity level: Note]
                [Group: Undecoded]
        Call-ID: 4b9a4b14-3ce32412@x.x.x.x
        [Generated Call-ID: 4b9a4b14-3ce32412@x.x.x.x]
        CSeq: 101 INVITE
            Sequence Number: 101
            Method: INVITE
        Max-Forwards: 70
        Contact: "xxxx" <sip:xxxx@x.x.x.x:5060>
        Expires: 240
        User-Agent: Linksys/SPA8000-6.1.12SR1
        Allow-Events: talk, hold, conference
        Content-Length: 444
        Allow: ACK, BYE, CANCEL, INFO, INVITE, NOTIFY, OPTIONS, REFER
        Supported: x-sipura, replaces
        Content-Type: application/sdp
    Message Body
        Session Description Protocol
            Session Description Protocol Version (v): 0
            Owner/Creator, Session Id (o): - 21225879 21225879 IN IP4 x.x.x.x
            Session Name (s): -
            Connection Information (c): IN IP4 x.x.x.x
            Time Description, active time (t): 0 0
            Media Description, name and address (m): audio 20827 RTP/AVP 0 2 4 8 18 96 97 98 100 101
            Media Attribute (a): rtpmap:0 PCMU/8000
            Media Attribute (a): rtpmap:2 G726-32/8000
            Media Attribute (a): rtpmap:4 G723/8000
            Media Attribute (a): rtpmap:8 PCMA/8000
            Media Attribute (a): rtpmap:18 G729a/8000
            Media Attribute (a): rtpmap:96 G726-40/8000
            Media Attribute (a): rtpmap:97 G726-24/8000
            Media Attribute (a): rtpmap:98 G726-16/8000
            Media Attribute (a): rtpmap:100 NSE/8000
            Media Attribute (a): fmtp:100 192-193
            Media Attribute (a): rtpmap:101 telephone-event/8000
            Media Attribute (a): fmtp:101 0-15
            Media Attribute (a): ptime:20
            Media Attribute (a): sendrecv
            [Generated Call-ID: d00bf67-6c3188fe@x.x.x.x]

Offline NEPhoneGuy

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 218
  • Country: us
  • Karma: +5/-0
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #5 on: May 07, 2020, 03:56:50 PM »
You get the same result with a 4 digit and external call?

Offline v2win

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 628
  • Country: us
  • Karma: +11/-0
    • View Profile
Re: Basic SPA8000 configuration to connect to MiVB with SIP Trunking
« Reply #6 on: May 08, 2020, 02:26:27 PM »
I have the deployment guide for this from Mitel. Its really old from Jan 2009.

send me a message with your email and I can send it on to you if you want it.


 

Sitemap 1 2 3 4 5 6 7 8 9 10