Author Topic: SX2000 card st not siezable  (Read 2581 times)

Offline Mark_Hutch

  • Contributer
  • *
  • Posts: 12
  • Country: gb
  • Karma: +0/-0
    • View Profile
SX2000 card st not siezable
« on: March 12, 2014, 08:26:41 AM »
Hello guys

had a red light on one of our PRI cards

Did a st (plid) and it came back with not siezable?
Busy'd plid and then RTS and came back the same?
What does not siezable mean and what would cause this?

Cheers

Mark


Offline lundah

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1213
  • Country: us
  • Karma: +66/-0
  • Senior Chief Grunt
    • View Profile
Re: SX2000 card st not siezable
« Reply #1 on: March 12, 2014, 08:31:59 AM »
Could be a few things. If there's only one port on the card in use, you could try re-loading the card to see if that brings it back. Otherwise you might have to have the carrier test the circuit. Also do a "DTSTAT READ <PLID>" and see if there's any errors.

Offline Mark_Hutch

  • Contributer
  • *
  • Posts: 12
  • Country: gb
  • Karma: +0/-0
    • View Profile
Re: SX2000 card st not siezable
« Reply #2 on: March 12, 2014, 08:49:48 AM »
Hey lundah

Did DTstst command ans got the following back
Link is not available, signalling medium lost                                   
         duty                             bit                                   
         cycle       framing              error                                 
Time     (%)         losses     slips     rate                                 
------------------------------------------------                               
13:01      0            0           0         0

Will contact our carrier and see what they say

Cheers

Mark

Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: SX2000 card st not siezable
« Reply #3 on: March 12, 2014, 09:40:17 AM »
If you use the command "DTS Read <Plid> last 24" it will show you if it has been up within the last 24 hours.

Ralph

Offline Mark_Hutch

  • Contributer
  • *
  • Posts: 12
  • Country: gb
  • Karma: +0/-0
    • View Profile
Re: SX2000 card st not siezable
« Reply #4 on: March 12, 2014, 10:17:16 AM »
Nice one ralph I think?


But what's the duty cycle % colum?

Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5767
  • Country: us
  • Karma: +469/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: SX2000 card st not siezable
« Reply #5 on: March 12, 2014, 10:48:20 AM »
The duty cycle show you the % of the given hour that the circuit was actually working.
A 0 (zero) would mean it was down for the entire hour.

Ralph

Offline Mark_Hutch

  • Contributer
  • *
  • Posts: 12
  • Country: gb
  • Karma: +0/-0
    • View Profile
Re: SX2000 card st not siezable
« Reply #6 on: March 12, 2014, 01:49:25 PM »
Right!

Thanks for that Ralph


 

Sitemap 1 2 3 4 5 6 7 8 9 10