ASU II

[Hus4in]

Dear All

We have a problem in release 4.1 3300 ICP ,our problem is ASU II (50005105) can't be detected in it, but if we connect to MCD.8.0 3300 ICP ,ASU II can detected.
Any some one help me,thanks for your kind attention.

Rgrds.

[ghost]

what do you get if you run "display asu info" in the maintenace commands?

[Hus4in]

Thanks Ghost.
This is display ASU info:

CIM         STATUS         UAPI TYPE ( HUBSP TYPE )     CARD INFO
------------------------------------------------------------------
1      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
2      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
3      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
4      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
5      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
 Cim1 Prom:
        FW:
 Cim2 Prom:
        FW:
 Cim3 Prom:
        FW:
 Cim4 Prom:
        FW:
 Cim5 Prom:
        FW:

[Hus4in]

This is connected with MCD 8.0 ,display ASU info:

CIM         STATUS         UAPI TYPE ( HUBSP TYPE )     CARD INFO
------------------------------------------------------------------
1      UAPI_APH_UP      DS_AMB_64 ( UK COMBO )   (55 00 51 50 00 )
2      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
3      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
4      UAPI_APH_UP      DS_ASU2G ( UK COMBO )   (00 00 )
5      UAPI_APH_DOWN      DS_HUBTYPE_NONE ( UNKNOWN )   ()
 Cim1 Prom: 50004870 56008157RC.04 08000F0075D5  1                                                                                         
        FW: MAC:08000F0075D5 | MAIN Ver:04.00.00.14 Date:Mar 05 2008 Time:07:54:08 | FLASH = MAIN
 Cim2 Prom:
        FW:
 Cim3 Prom:
        FW:
 Cim4 Prom: 50005105 56007252RA.05 08000F845F02                                                                                             
        FW: MAC:08000F845F02 | MAIN Ver:01.00.00.35 Date:Nov 05 2015 Time:14:07:17 | BOOT Ver:01.00.00.31 Date:May 08 2012 Time:10:27:50
   Slot 01:
   Slot 02:
 Cim5 Prom:
        FW:

[x-man]

Have you changed the programmed asu type in Analog service units form on the 4.1 system?

[Hus4in]

Thanks x-man

I have a program on analog service unit form,on the 4.1 system and here's the result:
Analog Services Units
   Controller Module Port Unit       Programmed Type       Installed Type       Comment                                                                                      
   -                0         Not Programmed      No Unit Present                                                                                          
   -                1     2      ASU II                      No Unit Present                                                                                          
   -                2         Not Programmed      No Unit Present                                                                                          
   -                3         Not Programmed      No Unit Present                                                                                          
   -                4         Not Programmed      No Unit Present                                                                                          

[x-man]

Have you programmed the rest of the form like the card type installed in the asu?

[Hus4in]

Thanks for your answered,

I have installed 24 port ONSp card on slot 1 but the system can't be dictected.

[x-man]

What does ASU info say now?

Have you got an IP conflict? ASU2 uses;

192.168.Y.1 to 192.168.Y.15
Where Y ranges from 10 to 13

These must not be used elsewhere on the system. What controller type do you have?

[Hus4in]

Thanks x-man
the problem is still the same, we setting IP 10.64.194.86 in the controller unit,
and we use MXe 3300 (4.1 system) with IDE hard disk.

[x-man]

"Upgrade bootrom all" from maintenance and if that fails you have a faulty ASU11. Do a "Status ASU ALL" from maintenance and it will probably show the cim port down (even though the lights are all up). Apparently a know fault from a bit of searching.