Messages

1

Mitel MiVoice Business/MCD/3300 / Re: Mitel private number not coming trough

« on: June 18, 2019, 08:32:07 AM »

Make sure all your SIP peer settings are correct for the SIP provider (is the SIP provider on the Interop list?)
Are you using an MBG?
Is SIP ALG turned off on the firewall?
What is in the header of the incoming SIP call?
Are there any incoming digit mods?

2

Mitel MiVoice Business/MCD/3300 / Re: Hunt Group Out of Service

« on: May 28, 2019, 11:10:05 AM »

Can any other site dial it?
Are there any SDS errors?
When you do a LOCATE NUMBER or LOCATE FEATURE EXT in maintenance commands, does it come back with anything?

3

Mitel MiVoice Business/MCD/3300 / Re: MiVoice Business 10

« on: April 16, 2019, 08:54:16 AM »

As far as i'm aware there are no rumblings of a v10 MiVB any time soon. v9 has just been released really

4

Mitel MiVoice Business/MCD/3300 / Re: Setup phones to be able to change outbound displayed number

« on: October 23, 2018, 11:51:59 AM »

The "Associated Directory Number" form might be the way forward if the issue is that you're running out of space in the CPN substitute form?

5

Mitel Software Applications / Re: MiVBE cannot logon to MiVB

« on: October 02, 2018, 04:54:56 PM »

***Resolved***

Issue was on the data centre side of things...the MiVBE obviously uses 2 IP's. They were both bonded on the VM NIC...but it actually needed to be bound to the SDN (Software Defined Network) as well!

6

Mitel Software Applications / MiVBE cannot logon to MiVB

« on: October 02, 2018, 11:03:48 AM »

Hi all,

Having issues with logging onto a MiVB within MiVBE.

This is in a virtual data center with other apps deployed okay. Licensed MiVBE okay and it has booted up the MiVB.

The IP address of the MiVB is in the same subnet BUT i literllay cannot logon to it even locally (same subnet). I initially loaded .301 software, and then went down to .202

Any ideas please?

7

Mitel MiVoice Business/MCD/3300 / Re: DLM License Violation

« on: October 02, 2018, 09:32:54 AM »

tmnt, I think what you need to do is a RMESS VERIFY command from the DLM controller to the one you replaced, see what the printout is.

Can you ping the other controller etc?

8

Mitel MiVoice Business/MCD/3300 / Re: DLM License Violation

« on: October 01, 2018, 11:43:51 AM »

A couple of things here, on the DLM form on the designated license manager, does it show the controller that was switched out in license violation?

When the other controller was swapped out, did you keep the iButton and put it in the new controller?

Is the other controller contactable?

9

Mitel MiVoice Business/MCD/3300 / Re: DHCP shows Bad_Address for some Mitel phones

« on: September 25, 2018, 01:27:01 AM »

The PBX definitely isn't giving out DHCP as well?

10

Mitel MiVoice Business/MCD/3300 / Re: Automated System Backup Routine

« on: September 21, 2018, 12:56:57 PM »

You'll need to setup your FTP credentials on the 3300, then set a schedule for the back to occur whenever you want

11

Mitel MiVoice Business/MCD/3300 / Re: 54002701MiVoice Business License-SINGLE LINE EXT

« on: September 21, 2018, 05:12:25 AM »

Just on the back of this, I use single line extension licenses for things like generic SIP phones via SIP ATA's for conference phones

12

Mitel MiVoice Business/MCD/3300 / Re: Ring Group to External Number

« on: September 21, 2018, 04:13:03 AM »

I know it's kind of the same thing, but maybe try setting up a hunt group with a divert to the external number and divert the ring group to the hunt group

13

Mitel MiVoice Business/MCD/3300 / Re: Mxe boot failure

« on: September 21, 2018, 04:10:16 AM »

Hi johnp,

I only have 1 disk in and I have cleared the sockets as well 

14

Mitel MiVoice Business/MCD/3300 / Mxe boot failure

« on: September 20, 2018, 06:30:34 PM »

Hi all! I am getting the below error when booting up and Mxe. I have a RAID controller with 2 disks. I am currently just trying to boot from 1 disk and it has the green access light on the back.

I have also tried to flash the drive and just run new software via FTP but it goes into the same error below...to me it's like it's not even seeing the drives?? For example, if I boot without any drives, it should show RAID controller detected Bay1/Bay2 no disks found

Any help will be greatly appreciated

boot device          : ata=0,0
unit number          : 0
processor number     : 0
host name            : bootHost
file name            : /partition4/RTC8260
inet on ethernet (e) : 192.168.1.2
host inet (h)        : 192.168.1.5
gateway inet (g)     : 192.168.1.254
user (u)             : ftp
ftp password (pw)    : @
flags (f)            : 0x0
other (o)            : motfcc

ataDrv: ataDriveInit failed on Channel 0 Device 0

Disk Configuration Started.
Creating block device for controller  0 drive 0... done.
Creating CBIO device for controller  0 drive 0... 0x1ecd5028 (tBoot): cbioWrapBl
kDev: BLK_DEV pointer 0x1f7ffe40 appears invalid.
done.
0KB added to /ata00 partition
free disk space after partition 0 is 0KB
Creating CBIO device for controller  0 drive 0... 0x1ecd5028 (tBoot): cbioWrapBl
kDev: BLK_DEV pointer 0x1f7ffe40 appears invalid.
done.
Attaching to partition table for 1 partitions on controller 0 drive 0... 0x1ecd5
028 (tBoot): cbioWrapBlkDev: BLK_DEV pointer 0x00000000 appears invalid.
ERROR: In usrAtaConfigExtended() failed to attach to partition table for control
ler 0 drive 0.
Error auto-loading file: errno = 0x850001.
Attached TCP/IP interface to motfcc0.
Attaching network interface lo0... done.
Getting boot parameters via tftp from 192.168.1.8:slot0.cfg.

15

Mitel MiVoice Business/MCD/3300 / Re: MiVB 9.0

« on: September 20, 2018, 11:10:48 AM »

ace, if you could report back about the RAM that would be great