1
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: MiVoice 400 DID to Public Phonebook
« on: September 10, 2024, 06:25:36 PM »
You can always use PISN...
News:
Welcome to Mitel Forums. The Mitel resource - by techies, for techies...
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: 5370IP Phones - VLAN via DHCP
« on: August 15, 2021, 11:45:18 PM »
Hope this documents will help..
BR
Zoran
BR
Zoran
3
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: SIP error message Not Enough License in PBX
« on: May 07, 2020, 04:16:11 PM »
Go to Terminals and check if any created terminals don't have assigned user - if found, delete terminal. This will release used license...If terminal is deleted from User screen - it's not really deleted - just not allocated to the user and will hold the license...
4
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Too many errors with the same ID
« on: February 28, 2020, 02:53:32 AM »
MiVoice 400 error list...https://1drv.ms/b/s!Aju8bIuuWmhWgYZybIDxWLLHWkljtg?e=4chScZ
Enjoy reading...
BR
Enjoy reading...
BR
5
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Mitel 622d not switching on blinking red
« on: November 20, 2019, 03:21:27 PM »
Try to follow this...
https://1drv.ms/b/s!Aju8bIuuWmhWhJcg_URuL1czhXMWzQ?e=XufhPW
https://1drv.ms/u/s!Aju8bIuuWmhWhJcfykAfQ4j4jGdDLQ?e=Hr1nuJ
Booter SW might be old - but phone should boot up...
BR
https://1drv.ms/b/s!Aju8bIuuWmhWhJcg_URuL1czhXMWzQ?e=XufhPW
https://1drv.ms/u/s!Aju8bIuuWmhWhJcfykAfQ4j4jGdDLQ?e=Hr1nuJ
Booter SW might be old - but phone should boot up...
BR
6
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Room Charges
« on: June 03, 2019, 04:44:45 AM »
Hi bvtech
Haven't tried, but search for Virtual charges - basically, you created multiple outgoing routes with different pulse interval and then use LCR to route calls to different routes (according to destination number)...if using FIAS, you should be able to send final charges (in $) down to interface - or shown in own Hospitality manager...
Good Luck
BR
Haven't tried, but search for Virtual charges - basically, you created multiple outgoing routes with different pulse interval and then use LCR to route calls to different routes (according to destination number)...if using FIAS, you should be able to send final charges (in $) down to interface - or shown in own Hospitality manager...
Good Luck
BR
7
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: 2 line keys on phones but second caller gets a busy signal
« on: March 11, 2019, 03:33:30 AM »
Try - terminal -> Multi lines -> select 3 (default 1), permission set -> busy on busy -> untick...
BR
BR
8
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Aastra IP RFP42 DeTeWe
« on: December 29, 2018, 04:34:56 PM »
PM sent
9
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Out of Service
« on: February 10, 2018, 10:23:28 PM »
Errr...yes
10
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Out of Service
« on: January 12, 2018, 04:14:03 PM »
Hi mate
First, check your license - how many Mitel SIP terminals are availble there? If 6, then go to Terminals and check if you have terminals created without users - if yes, delete those terminals...If unsure, post a screenshot here...
BR
First, check your license - how many Mitel SIP terminals are availble there? If 6, then go to Terminals and check if you have terminals created without users - if yes, delete those terminals...If unsure, post a screenshot here...
BR
11
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: DSP/EIP MITEL
« on: December 20, 2017, 02:36:42 PM »
There is no simple answer to your question - again, will depends of your system config, network, SIP provider...
Eg. - you will using FXO - in order to communicate with IP (SIP) terminals, you will need Voice channels and DSP resource for transcoding. You will using SIP trunks - can you sucessfuly answer and transfer a call? If you have problem with transfer - then you need to route voice traffic thru the system - you need DSP. Can you make sucessful call and transfer between extensions on different nodes? If no - (sometime network config don't allow direct media routing between terminals) - you will need DSP...
In all my installation I have enough DSP's (or EIP) to satisfy all above - hard learned lesson on one of the first install...
But, it's your call...
BR
Eg. - you will using FXO - in order to communicate with IP (SIP) terminals, you will need Voice channels and DSP resource for transcoding. You will using SIP trunks - can you sucessfuly answer and transfer a call? If you have problem with transfer - then you need to route voice traffic thru the system - you need DSP. Can you make sucessful call and transfer between extensions on different nodes? If no - (sometime network config don't allow direct media routing between terminals) - you will need DSP...
In all my installation I have enough DSP's (or EIP) to satisfy all above - hard learned lesson on one of the first install...
But, it's your call...
BR
12
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: Got some Questions about the MiVoice 470
« on: December 19, 2017, 08:52:44 PM »
Hi fbp
1. No - 300Mb should be unlocked by applying Enterprise VM license - nothing to do with SWA (tried restart the system?)
2. Control outputs - never tried - but you will need FXO port -> change port type to Control output in Configuration ➙ System ➙ Interfaces ➙ Analogue ➙ Analogue terminal interface (entry). Then, according to the document, you can open with *74 <Call number1)> or close with #74 <Call number1)>.
More info in document syd-0570, page 474.
BR
1. No - 300Mb should be unlocked by applying Enterprise VM license - nothing to do with SWA (tried restart the system?)
2. Control outputs - never tried - but you will need FXO port -> change port type to Control output in Configuration ➙ System ➙ Interfaces ➙ Analogue ➙ Analogue terminal interface (entry). Then, according to the document, you can open with *74 <Call number1)> or close with #74 <Call number1)>.
More info in document syd-0570, page 474.
BR
13
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: DSP/EIP MITEL
« on: December 19, 2017, 08:36:24 PM »
Hi Harrabi
Depends of quantity of those licenses (eg. number of voice channels, number of SIP access channels...,), your SIP provider config (do you need routing of media traffic thru system?), network settings Master - satellite (same as for SIP access channels),...
If you are configured A470 thru Mitel CPQ - number of required voice channels will be suggested in Result tab and necessary part (DSP or EIP) will be added to the config automatically...
BR
Depends of quantity of those licenses (eg. number of voice channels, number of SIP access channels...,), your SIP provider config (do you need routing of media traffic thru system?), network settings Master - satellite (same as for SIP access channels),...
If you are configured A470 thru Mitel CPQ - number of required voice channels will be suggested in Result tab and necessary part (DSP or EIP) will be added to the config automatically...
BR
14
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: SIP Trunk
« on: November 14, 2017, 01:56:46 PM »
Hi mate - yes, you need SIP trunk license for each trunks...depends of extensions used, maybe you need addititional DSP resources (and possible Voice channels license - again, depends of your system config)
BR
BR
15
Aastra - MiVoice Office 400 and MiVoice MX-One / Re: No SMDR raw data output from Mitel A-470
« on: May 24, 2017, 04:52:32 PM »
Another good program for testing...http://www.aggsoft.com/pbx-data-logger.htm
Its only demo, but good enough for testing...Also, upgrade 470 to the latest (or at least 4.1 HF2) to get enhanced SMDR report...
BR
Its only demo, but good enough for testing...Also, upgrade 470 to the latest (or at least 4.1 HF2) to get enhanced SMDR report...
BR
Pages: [1] 2