Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jf1221

Pages: [1] 2
1
Mitel MiVoice Business/MCD/3300 / aastra 6730i phone will not transfer or set up conf call correctly on mitel 3300
« on: March 28, 2016, 10:18:18 PM »
I have just set up 7 new aastra phone 6730i with an updated firmware. I cannot get the transfer or conf feature on the phone to work correctly.
for the transfer, i put the call on hold, hit the fixed transfer button, dial the number and hit transfer, it does the transfer to the new ext, but it rings once and call dies.
Is this a COS issue.

2
Mitel MiVoice Business/MCD/3300 / upgrade 3300 from 7.0 to 7.2
« on: December 08, 2015, 01:57:39 AM »
Is it possible to upgrade from 7.0 to  7.2?
If so, can you layout the step by step procedures involved with the software components?

3
Mitel MiVoice Business/MCD/3300 / Re: How do i configure my 3300 cxII to use analog lines
« on: May 19, 2015, 03:30:05 PM »
ok. so did that and i am almost there...i am having truble with outbound calling. I have been playing and tweaking the ARS, to no avail. everytime i try calling locally. I get the message that the number cannot be completed as dialed. I am stripping the 9, i have tried to send 7 digits and 7 digits plus 3 for area code.  also inbound works, but my phones dont start ringing till the 4th ring. Is this a CO tone detection problem?

4
Mitel MiVoice Business/MCD/3300 / How do i configure my 3300 cxII to use analog lines
« on: May 18, 2015, 03:59:12 PM »
I have the on board 6 LS trunks that I want to uses with my two analog lines in the US for incoming and outgoing calls? I have programmed PRI's and SIP circuits before, but never analog phone lines.

5
Mitel Software Applications / How do I set up MAS & BGW so my UCA client can access via teleworker
« on: July 10, 2014, 10:15:26 PM »
How do I set up MAS & BGW so my UCA client can access via teleworker?

I have my MAS server working with UCA clients internally. However, i would like to use my softphone from home. so how do i set up the MAS server and Border gateway.
I currently have a separate BG on the DMZ for my teleworker phones. I read that i have to cluster that unit with the BG in the MAS server? I know that i will have to create an A record with my provider that resolves my MAS server name to a public IP address. Help.

6
Mitel MiVoice Business/MCD/3300 / Re: One Way Audio on Boder gateway
« on: July 09, 2014, 03:50:19 PM »
Custom

RTP ICP-side override addresses    192.168.50.16
RTP Set-side override addresses    40.140.209.195

no phone is on a seperate network...pure teleworker

7
Mitel MiVoice Business/MCD/3300 / Re: One Way Audio on Boder gateway
« on: July 09, 2014, 03:46:59 PM »
Custom configuration: RTP ICP 192.168.50.16

8
Mitel MiVoice Business/MCD/3300 / One Way Audio on Boder gateway
« on: July 09, 2014, 03:25:27 PM »
my teleworker phone makes phone calls and the party on the remote end can hear him vai cell phone.Bu the teleworker cannot hear the cell phone user. calling throuh SIP provider windstream. Firewall ports are open and routing is in place. where can i look on the Border gateway to view the errors or logs.

9
Mitel MiVoice Business/MCD/3300 / Re: 420 bad extension on my vMCD
« on: July 09, 2014, 03:18:21 PM »
that was it Ralph...
In checking the pcap I can see in the invite a "Require: 100rel"   - pure guess on my part but in the SIP profile turn off Reliable Provisioning.



10
Mitel MiVoice Business/MCD/3300 / 420 bad extension on my vMCD
« on: July 08, 2014, 11:13:59 PM »
I cannot dial out...I can receive phone calls, but outbound is not working...i took some captures and I am getting a 420 bad extension. the provider is Windstream

11
Mitel MiVoice Business/MCD/3300 / Re: SIP trunk between cucm 7.1 and Mitel 3300
« on: March 25, 2014, 07:45:24 PM »
I keep getting an error has occurred when i am trying to post...can i email it to you?

12
Mitel MiVoice Business/MCD/3300 / Re: SIP trunk between cucm 7.1 and Mitel 3300
« on: March 25, 2014, 07:07:48 PM »
Absolutely...i was just about to do that and post....standby

13
Mitel MiVoice Business/MCD/3300 / Re: SIP trunk between cucm 7.1 and Mitel 3300
« on: March 25, 2014, 06:55:25 PM »
What are your significant digits : all
CSS under the inbound section set to css-sat-device
 Does the CSS include the partition that the phone is in.. It does now.

so I changed the CSS to css-sat-device on everything and i can call from Mitel to cisco phone.... Mitel phone 2210 -----> cisco phone 3320...However, when i pick up on cisco, it goes to fast busy. When i try to dial on the Cisco phone, as soon as i hit the second 22XX, i get dial tone....if I ignore it and dial all the way, i get a fast busy.

14
Mitel MiVoice Business/MCD/3300 / Re: SIP trunk between cucm 7.1 and Mitel 3300
« on: March 17, 2014, 12:57:47 PM »
yes, those are the correct IPs. On CUCM, the ext 3320 does exist and does work. It does a css and partition. however, according to the PDF that i have attached, it doesn't mention anything about creating additional CSS or partitions, just a route pattern. I have attached the PDF. Did I miss something on the PDF?

15
Mitel MiVoice Business/MCD/3300 / Re: SIP trunk between cucm 7.1 and Mitel 3300
« on: March 15, 2014, 10:40:12 AM »
it's to call manager no cube involved...uploaded two files.

Pages: [1] 2