Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mickyspring

Pages: [1]
1
Mitel MiVoice Business/MCD/3300 / Problem's setting up a 5302 set
« on: August 17, 2015, 03:41:34 PM »
I've programmed a 5302 IP set and found 2 different way's to initialize the phone and neither way is working.  I have deleted one of them and rebuilt it , but the lights just flash after going through the initialization process.

2
Thanks.... Found it under system speed call #**0916.

3
Mitel MiVoice Business/MCD/3300 / Find a POTS line coming in on a T!
« on: June 03, 2015, 07:21:11 PM »
I have a POTS line (3102750916) coming in on a T1 and can't find where it programmed it in the system.  I think it's pointing to another number but I don't know what it is.

4
Does anybody know if there is a default login and password for the Streamline unit ???

5
Problem is there are no indicators or light on the unit to show any activity.

6
I have a cable that has been cut and pulled out and not able to trace back the the main phone room and i need to figure out what port the phone was set up on.  This is was i found in the maint command line and i'm figuring that 1-3-1-48 is the port number, but if i pull the cross connect on a known working phone on port 1-3-1-51 it still shows as IDLE. I'm looking at the 110 blocks and i figure that there are 24 ports to each 25 pair cable and 1-3-1-48 would be the last one on the second cable.  Am i right in thinking that ????

 Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  48  1| 5330e IP             |Out of Service |         |      |         
 1 3  1  48  2| Unassigned           |Not applicable |         |      |         
 1 3  1  48  2| Alternate Codec      |Out of Service |         |      |         
----------------------------------------------------------------------------   
  Location    | Device               | State         |  Owner  | ID   |Status   
----------------------------------------------------------------------------   
 1 3  1  51  1| 5330e IP             |Idle           |         |      |         
 1 3  1  51  2| Unassigned           |Not applicable |         |      |         
 1 3  1  51  2| Alternate Codec      |Idle           |         |      |         
----------------------------------------------------------------------------   

7
Mitel MiVoice Business/MCD/3300 / Re: Compatibility of 5201 & 5302 IP phones
« on: September 06, 2013, 02:16:05 PM »
SORRY... It's a 3300 MCD.

8
Mitel MiVoice Business/MCD/3300 / Compatibility of 5201 & 5302 IP phones
« on: September 06, 2013, 02:14:00 PM »
I have a 3300 ICP with a stratus server and I'm looking for IP phones with no displays.  Would the 5201 & 5302 IP phones be compatible ? 

9
Mitel MiVoice Business/MCD/3300 / Re: Deleting and adding a EHDU
« on: August 22, 2013, 09:25:10 PM »
Had to look at the suite programming.  Line 2 wasn't listed as a second member.

10
Mitel MiVoice Business/MCD/3300 / Re: Deleting and adding a EHDU
« on: August 22, 2013, 11:18:11 AM »
These are analog lines.  The numbering is really odd, as the main room number is 7xxx and the second line is 8*17xxx.  Not sure , but i think i have to make sure that the 2nd line is noted in the stratus server on the 1st line ????

11
Mitel MiVoice Business/MCD/3300 / Deleting and adding a EHDU
« on: August 20, 2013, 11:06:55 AM »
I have a 3300 with a Stratus server 6.0, and i'm getting a busy on line 2 in one of the rooms (line 1 has dialtone).  Would deleting and moving Line 2 from the PLID solve the issue, or is it a programming issue.  This is located in a hotel where all rooms have two lines.  If I have to delete line 2 what would be the procedure to do that ?

12
Mitel Software Applications / NuPoint MWI's on but no messages
« on: October 23, 2012, 02:15:57 PM »
I have a Nortel OPT 81 with a NuPoint 7.0 and it lost power, but now I have some phones with the MWI on but no messages. Any ideas ?

Pages: [1]