Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - minshad

Pages: [1]
1
Mitel MiVoice Business/MCD/3300 / Re: Install Mitel Business Console
« on: October 27, 2021, 05:46:57 AM »
run wizard without tick (console has administrator access)

2
How we can block incoming call to DID number except one mobile number. from whitelist mobile they will be able to call all other DID and whitelist one.

after i programmed whitelist, if i dial any other DID number call goes to whitelist DID number

3
Mitel MiVoice Business/MCD/3300 / Re: upgrading V7 to V8 booting issue
« on: March 30, 2021, 05:52:13 AM »
now unable to boot. even though software installer not working. it stay upgrade in process.

4
Mitel MiVoice Business/MCD/3300 / upgrading V7 to V8 booting issue
« on: March 30, 2021, 03:26:04 AM »
lost connection upgrading and cant boot. later found below issue and controller not booting. does anyone know ! 

Upgrade_Manager::dataTagHandler onlineUpgrade [NO]
Initializing Backup
Initializing Software Install
Platform type is MXeIII
the vmail file version curr - 14.0.2.9
 new - 14.0.2.9

Initializing License
Initializing Restore
Upgrade_Backup is complete
ProcessState complete for Backup
Upgrade_SWInstall::setExternalAction
External action is Action=FileTransferOnAction|File3300=/inactive/sysro/3300SW_T                       OC.txt|FileRemote=C:\Program Files (x86)\Mitel\MiVoice Business Software Install                       er\Ftp\ICP3300_14.0.3.51\FTP/3300SW_TOC.txt|NumRetries=3|
ProcessState waiting for external action for Software Install



5
Mitel MiVoice Business/MCD/3300 / mitel E2T booting issue
« on: July 20, 2019, 06:44:46 AM »
it keep booting after mistakenly changed e2t card address from UBOOT


U-Boot 2015.10 (Apr 04 2019 - 15:25:14 -0400) mxeiii 1.0.3.8

Reset Status:

CPU:   e300c1, MPC8360EA, Rev: 2.1 at 528 MHz, CSB: 264 MHz
Board: Mitel MXe-III, U-Boot 2015.10 (Apr 04 2019 - 15:25:14 -0400) mxeiii 1.0.3.8
Refresh UBOOTROM

Reset Cause (0x3 - EXTERNAL_INTERNAL_SOFT_RESET)

       Watchdog enabled
I2C:   ready
DRAM:

Configuring DDR2 SODIMM using SPD drivers
DDR
Starting POST...

SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
SDRAM CS1 Address  Walk 1................... PASSED
SDRAM CS1 Address  Walk 0................... PASSED
SDRAM CS2 Address  Walk 1................... PASSED
SDRAM CS2 Address  Walk 0................... PASSED

1 GiB (DDR2, 64-bit, ECC off, 264 MHz)
Flash: 4 MiB
PCI:   Bus Dev VenId DevId Class Int
PCI:
  00:16.0     - 1095:3512 - Mass storage controller
In:    serial
Out:   serial
Err:   serial
Found valid environment in flash.
Slot id 0

do_mitel_stuff_inram Tests...
SATA RAID Controller Detected.
Sil5923Reset - Done
Rebuild - Max transfer 6, Min transfer 0, Rebuild Inc 0
Bay 1 is disk operational.
Bay 2 is disk operational.
Net:   UEC0

do_mitel_ethstuff_inram Tests...

do_mitel_programfpga Tests...
FPGA version 0002:6123 loaded


E2T card installed; wait for 10s to let it run its preboot command...

Press <SPACE> key 3 times within 7 seconds to stop autoboot

UEC: PHY is Generic MII (143bc31)
UEC0: Full Duplex
UEC0: Speed 100BT
UEC0: Link is up
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16

Retry time exceeded; starting again
Booting VxWorks E2T image with DHCP configuration...
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16

Retry time exceeded; starting again
Could not load E2T8260...




6
SIP On Mitel / Outging Call Disconnect after 15 second
« on: July 19, 2019, 05:43:53 AM »


out going call disconnect after 15 seconds.
using softphone(linephone) checked direct connection from router, it works fine.
For sipnatting using CISCO router
incoming call ok

Hardware : Mitel 3300

7
thank you.

found it. from system menu it was there.
P1 is programmed as system menu.


9
i couldnt find call forwarding feature in mitel 6863i phone.

Pages: [1]