Mitel Forums - The Unofficial Source
Mitel Forums => Mitel MiVoice Business/MCD/3300 => Topic started by: Helis on April 09, 2010, 09:34:08 AM
-
Hi,
After RESET SYSTEM 3300 CXi II donot boot and Console print:
MITEL SYSTEM ROM R3.0/6 May 26 2009 (100 - SOFTWARE_RESET)
CCA Number : 56008216 RC.1
System Model : 00610001 F100
CPU Model : 8360 R8048000021
Reset Config Low : 08030008
Reset Config High : b4500006
Coherent System Bus Clock (MHz) : 266
CPM Clock (MHz) : 266
Core Clock (MHz) : 399
DDR Clock (MHz) : 133
Local Bus Clock (MHz) : 66
Input Clock (MHz) : 33
Internal Memory Map : f0000000
Main Memory (MB) : 512
Local Memory (MB) : 0
Flash Memory (MB) : 2
MAC Address : 08000f51548a
L2 Switch : 1
POST Bypass : 0
Watchdog Bypass : 0
Slot Id : 0
Starting POST...
SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
SDRAM CS1 Address Walk 1................... PASSED
SDRAM CS1 Address Walk 0................... PASSED
SDRAM CS2 Address Walk 1................... PASSED
SDRAM CS2 Address Walk 0................... PASSED
Starting vxWorks...
VxWorks System Boot
Copyright 1984-2002 Wind River Systems, Inc.
CPU: Mitel Embedded PPC83XX F100
Version: VxWorks5.5.2
BSP version: 3.0/6
Creation date: May 26 2009, 11:27:13
Press <SPACE><SPACE><SPACE> to stop auto-boot AFTER countdown starts...
<7><6><5><4><3><2><1><0>
auto-booting...
boot device : ata=0,0
unit number : 0
processor number : 0
file name : /partition1/rtc8260
inet on ethernet (e) : 192.168.1.2:ffffff00
gateway inet (g) : 192.168.1.1
user (u) : ftp
ftp password (pw) : @
flags (f) : 0x0
other (o) : qefcc
Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
0KB added to /partition1 partition
free disk space after partition 0 is 0KB
0KB added to /partition2 partition
free disk space after partition 1 is 0KB
0KB added to /partition3 partition
free disk space after partition 2 is 0KB
0KB added to /partition4 partition
free disk space after partition 3 is 0KB
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/partition1) on controller 0 drive 0... done.
Creating Cache Layer for partition 1 (/partition2) on controller 0 drive 0... done.
Creating Cache Layer for partition 2 (/partition3) on controller 0 drive 0... done.
Creating Cache Layer for partition 3 (/partition4) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/partition1) on controller 0 drive 0... done.
Creating Dos FS device for partition 1 (/partition2) on controller 0 drive 0... done.
Creating Dos FS device for partition 2 (/partition3) on controller 0 drive 0... done.
Creating Dos FS device for partition 3 (/partition4) on controller 0 drive 0... done.
Disk Configuration Complete.
Loading /partition1/rtc8260...n/a
Error loading file: errno = 0x380003.
Can't load boot file!!
and restarts.
Whether who met such situation and what to do
Thankful in advance for the help
Thanks in advance
Andrey
-
What software version are you running and what caused the system to reboot?
-
Software version are MCD 4.1. Yes I program phonesi by ESM "System Administration Tool". When I lost network connection with controller I Ping it and receive - Time out.
-
For grins, add this line to your config:
other (o) : FixPartition
Ralph
-
Nothing has occured Red is Red :( Thanks for attempt to help me!
-
Change /partition1/rtc8260 to /partition4/rtc8260 and see if that makes a difference.
-
I assume your system was upgraded from an earlier release?
The upgrade process will create another partition on the HDD and put the new software there. As to why your system was trying to use partition1 I do not know.
-
Unfortunately the system was not restored.
partition1 or partition4 all early gives out the same mistake.
Loading /partition4/rtc8260...n/a
Error loading file: errno = 0x380003.
Can't load boot file!!
-
If you have a backup of the system, I suggest a manual install of the software and restore the DB from backup.
-
Thanks all.
It was necessary anew reinstall system.
The mistake MIPS *** Autoboot failed *** has remained.