Topics

1

Mitel MiVoice Business/MCD/3300 / mitel phones autocomplete when dialing numbers from history or phone book featur

« on: October 19, 2016, 02:51:48 AM »

Dear All,

I was using linksys phones that has feature that when you start dial number by typing first 2 or three disgits; it shows you a list of available numbers from history or from phone book for all numbers that has the same digits of the typed digits (like mobile contacts on android), so is there any similar feature  in mitel phones like mitel 5320e??

thanks

2

Mitel MiVoice Business/MCD/3300 / smdr caller id

« on: November 09, 2015, 05:17:18 AM »

 I telenet on port 1752, i can not see the caller id for incoming calls and it shows the trunk number T001 instead of the caller id?we have analog trunks and the answer point is set to an extension

3

Mitel MiVoice Business/MCD/3300 / smdr for incoming caller id

« on: November 05, 2015, 07:17:12 AM »

hi

when I telenet on port 1752, i can see the caller id for incoming calls and also for dialed (outgoing calls) without any problem. but now i am using software (simplesmdr or advanced pbx logger) and it shows only the outgoing calls numbers but for the incoming calls it shows only T001 instead of the caller id??

4

Mitel MiVoice Business/MCD/3300 / could not access administrator mailbox

« on: October 28, 2015, 02:46:50 AM »

i am trying to access administrator mailbox by dialing 9999 or (*9999 it says invalid) so is there any prerequisite so i can access the administrator mailbox??

5

Mitel MiVoice Business/MCD/3300 / hunt group for department

« on: June 15, 2015, 03:12:15 AM »

hi

i want to configure a hunt group for one department so when someone calls any member of that dept and that member didn't answer after 5 rings then the call automatically forwarded to next member of that dept

6

Mitel MiVoice Business/MCD/3300 / simple way to prevent international calls for specific users

« on: June 08, 2015, 04:01:00 AM »

Dear All

Could you please tell me how a simple way to prevent international calls for specific users?

7

Mitel MiVoice Business/MCD/3300 / remote office setup.... please help

« on: March 25, 2015, 07:24:37 AM »

Dear all,

I have mitel 3300 in the main site with 10 mitel phones, now we have new remote site with 5 users (5 phones), we wil configure IPSEC site to site vpn between the two sites, now we want the 5 phones in the remote site to be registered in the main site so we can make internal call with the remote site users and also the remote site users will make call through the mitel 3300 in the main site, i want to know the needed configurations on the phones that needs to be changed also if there any settings that needs to be applied on the mitel 3300?? 

8

Mitel MiVoice Business/MCD/3300 / activate call waiting

« on: February 24, 2015, 06:17:29 AM »

Dear All,

i want to activate call waiting for internal calls, it is activated for external calls, when i try to call busy extension it forward the call to the hunt group or get busy tone (depends if the user is part of a hunt group or not) and the other extension dont know that i am trying to call him or event didnt get message or call waiting tone,

I read about camp on but i think camp on is for external calls only, now the value of campon timer is 10 sec and also campom recall timer is 10 sec.

9

Mitel MiVoice Business/MCD/3300 / analog trunk did

« on: February 12, 2015, 02:42:58 AM »

Dear All,

I have 4 analog lines connected to mitel 3300 CXI (the 4 analog lines are in the same trunk group) and its working perfectly, now i have one employee (extension) want to have its own number (analog trunk did) so all incoming calls for that analog trunk number  will be routed to this extension (i did that) and all outgoing calls from this extension must use this analog trunk (i could not do that, ) so how can i route all outgoing call from an extension to be done from specific analog trunk? or how can i configure DID for analog trunk?

10

Mitel MiVoice Business/MCD/3300 / Day Night 1 Night 2 hours

« on: February 02, 2015, 02:40:27 PM »

Dear all,

I want to know what is the default settings for Day Night 1 Night 2 hours in class of service? (I mean the setting day from which hour or start time, for ex from 8 am to 4 pm) so how can i know or where i can find this ? also if i want to change these settings how??