Author Topic: Problem with programming T1/E1 Framer  (Read 4260 times)

Offline jarpaz

  • New Member
  • *
  • Posts: 3
  • Country: pl
  • Karma: +0/-0
    • View Profile
Problem with programming T1/E1 Framer
« on: November 17, 2015, 08:49:05 AM »
Hi,

I would like to ask for help with Dual T1/E1 Framer.
When I used first port as PRI everything was OK.
I have configured the second port as below (the same like the first one):

Protocol :               PRI
Logical link number:     3
ESM link number:         9
Framing mode:            E1
Protocol variant:        EURO_ISDN
NetworkSide:             FALSE
Termination mode nt/lt:  NT
e1_CRC4:                 TRUE
Impedance:               120 ohms
t310Timer:               40
t304Timer:               30
Resiliency:               Off


Protocol :               PRI
Logical link number:     4
ESM link number:         10
Framing mode:            E1
Protocol variant:        EURO_ISDN
NetworkSide:             FALSE
Termination mode nt/lt:  NT
e1_CRC4:                 TRUE
Impedance:               120 ohms
t310Timer:               40
t304Timer:               30
Resiliency:               Off

And after that I have alarms in controller (MXe with MCD 6.0) like below:

PRI Logical link number: 4
Layer 1 Status:  RED
Layer 2 Status:  DOWN
Interface Activated: TRUE

Any solutions?

Jaro


Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4100
  • Country: us
  • Karma: +133/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
Re: Problem with programming T1/E1 Framer
« Reply #1 on: November 17, 2015, 09:50:31 AM »
Do you have a PRI circuit connected to the 2nd port and a digital link license to provision it?

If you do not have a configured, operational PRI actually connected, it will be in alarm.

Offline jarpaz

  • New Member
  • *
  • Posts: 3
  • Country: pl
  • Karma: +0/-0
    • View Profile
Re: Problem with programming T1/E1 Framer
« Reply #2 on: November 17, 2015, 11:26:10 AM »
I have Digital Link licenses.

What I have done:
1. Hardware
- port -> up as E1
2. Trunk
- Trunk Attributes -> CoR and CoS set
- Digital Link Descriptors ->

Number      2
Address for Message Control      B
BER - Maintenance Limit, 10**-n      4
BER - Service Limit, 10**-n      3
Data Call Alternate Digit Inversion      No
Framing Losses in 24 hrs - Maintenance Limit      255
Framing Losses in 24 hrs - Service Limit      9000
Integrated Digital Access      ISDN NODE
Vendor Inter-working Type      
Satellite Link Delay      No
Slip Rate - Maintenance Limit (slips/24hr.)      5000
Slip Rate - Service Limit (slips/24hr.)      7000
Alarm Debounce Timer - Service Limit (millisec.)      500
Voice Encoding      Nil
Data Encoding      Nil
QSIG Private Network Access      No
Digital Link Fault Delay Timer (sec.)      240
Termination Mode      NT
Send Malicious Call Indication to PSTN for Tagged Calls      No
Inhibit sending Mitel Specific Info      No
T1 Only:
   B8ZS Zero Code Suppression      Yes
   Operation Mode      DSX-1
   CSU Tx Line Build-Out (dB.)      
   DSX-1 Line Length (Ft.)      0-133
   Extended Super Frame      Yes
   Inverted D channel ( DPNSS only )      No
   T1-619a Signalling ( MLPP only )      No
E1 Only:
   CRC-4 Enabled      Yes   
   E1 Line Length (Ft.)      0-133   
   E1 Impedance (Ohms)      120   

- Digital Links -> module added with DLD ->2
- MSDN -> added with Universal E1, Incoming and Local Office (I do not know if its necessary)
- Digital trunk - added Cabinet 4 with 30 trunks
- Trunk Groups -> added Trunk Groups Number ->2 with Circular Hunt Mode and creating Trunk Group Members
- ISDN Protocol -> added Controller Module ->

Controller Module      2   
Port      2   
Link Number      10   
Interface Type      E1   
Protocol      Euro ISDN   
Protocol Variant      Euro Standard   
Network side/Q.SIG Master      False   
Enbloc      False   
               
               
               
               
               
               
Enable NI2 Service Messages      False   
               
Replace External CLID      False   
Euro-ISDN Only
   T310 Timer (sec.)      40                                          
   T304 Timer (sec.)      30                                          
   Replace Incoming CgPN with Original Dialed Number      False                                          

Q.SIG Only
   Fake Answer Supervision      True                                          
   Sequential Channel Numbering      False                                          
   Enable Prefix Insertion      True                                          

- Advice of Charge -> added Controller Module with Euro ISDN

I did not configure ARS because of alarms.

What have I done wrong?

Offline jarpaz

  • New Member
  • *
  • Posts: 3
  • Country: pl
  • Karma: +0/-0
    • View Profile
Re: Problem with programming T1/E1 Framer
« Reply #3 on: November 19, 2015, 11:17:30 AM »
Any hints? :(


 

Sitemap 1 2 3 4 5 6 7 8 9 10