Mitel Forums > MiVoice Office 250/Mitel 5000

How to connect a node to a remote paging system

(1/1)

JeffonJohnsIsland:
I want to install a paging system in a location different from the node.  Paging system is about 1,800 to 2,000 feet away from node.  Paging system is a Bogen PCM, which can accept a trunk or extension/station for paging input.  Node is a HX box.

Options I am aware of are:
1. ATA using a FXO or FXS.  Doesn't look like I can add this to a page zone, however I could create a phantom, add it to the page zone and forward the phantom to the ATA, which would then connect to the page system

2. Connect a 5320 speaker to the paging system amp, wouldn't use the Bogen PCM.

3. Connect a node LS trunk to a set of ATA in peer mode, which then would connect to the page system.

4. Don't bother connecting the Bogen to a page zone, just use an ATA and program phones with that extension and//or tell people to call the ATA extension to page. 

I have seen IP paging modules by Teracomm.  Perhaps they have something that would work. 

I would guess others have dealt with this before and have better solutions than I have mentioned above or how do you handle this sort of situation.  I wish I could just add a SIP extension to a page zone. 

Thanks in advance for any ideas to stop me from pulling out more hair.  :)

Jeff

 



3. Run a long A$$ cable from the node LS to the paging system.  25 pair cable is already in place for part of run, not sure of gauge.

Tech Electronics:
Jeff,

I am going to assume you don't have copper that would allow you to connect directly to that site.

That being said it depends on whether or not you want it to be in a Page Zone or not. As you probably already know you can only put Digital/IP Phones, Trunks or Paging Interfaces in a Page Zone, basically no direct SIP devices.

Now that doesn't mean you can't use something like the Valcom V-811A or V-821A and then push that over via SIP to another Valcom Paging Device, kind of like what you want to do with option 3.

I know Valcom is a bit expensive, but you may be able to find something comparable by Viking Electronics, Bogen or Terracom. Basically, you are looking for a SIP Gateway that will allow you to use FXO/FXS/Paging Interface that would then connect to another SIP Device at the other location. This is assuming that the network is extended between the two sites in one way or another.

Thanks,

TE

JeffonJohnsIsland:
TE,

A million thanks for the ideas. 

What I didn't finish adding to the post is we do have 50 pair copper part of the way and 25 pair copper the remainder of the way from the node to the paging system amp location.  Distance between node and paging system is about 1,800 to 2,000 feet.  I didn't think the copper would carry sound 2,000 feet--I was thinking of line level sound, not a telephone line.  When you mentioned copper, I realized it's a telephone line/signal/sound, not line level sound.  Kind of a 'Doh" moment.  Thanks, thanks, thanks!

My work duties include telephone, paging and a an assortment of other duties.  It would be nice if I could be responsible for just telephones, so I could keep sharp in that area.  When I work in something (like paging) once a year or every other year, it's a bit tough for me.  Such is life and I will find some cheese to go with that whine... :)  In another three weeks, it will be behind me as I will be retiring.  A new challenge, and one I am mostly looking forward to.  I appreciate all the information I have learned and the help I have received on this forum. 

I (and my replacement) will connect the cables and see what the paging system sounds like from a LS on the node to the paging system.  Six to eight hundred feet of the cable is somewhat iffy, the cable is PE, but not icky pic and is run through underground conduit.  There are three other 25 pair inside type cables in the same conduit and they have had issues with cross talk. We haven't used the 25 pair PE cable in a while, so maybe (I can't remember) there is a good pair in the cable we can use.   I will post with the results, it might be early next week.

TE, thanks, thanks, thanks,

Jeff, who will be on John's Island full time soon.

JeffonJohnsIsland:
Unrelated to the paging system, but I think it was a nice fix, only took me a while to figure it out.  Maybe it will help someone else. 

We only have four nodes.  Most locations are at warehouses/offices associated with growing and packing apples.  One is at a golf course, with a restaurant.  I switched them from a Avaya Partner to a node on our Mitel system a while back.  They were frustrated with Google Reservations, after I switched them from the Partner to Avaya it started calling the wrong number for reservations.  The number Google started calling (via DEE) was an employees cell.  I fixed Google calling wrong number by pointing the number at the restaurant phones, bypassing the phone tree.  Not ideal.  I finally figured out Google reservations always showed the same caller ID.  So I added the number Google used to call routing table three and pointed it to the restaurant phone extensions--like how I route harassing phone callers to a very long pause/greeting/dead air in a CRA, then it hangs up.  Yes, that is whack-a-mole, but works for unsophisticated callers.  Then I was able to route the restaurant number back to the phone tree and they were happy, yea. 

Anyway, maybe this will help someone else.  Again, thanks to everyone who has helped me and thanks for the knowledge in this forum. 

Jeff

Tech Electronics:
Jeff,

I remember when you first got on the forums awhile back so it is good to hear that you are going to finally get to retire and enjoy your time there.

Thanks,

TE

Navigation

[0] Message Index