Author Topic: The SYSTEM FAIL TRANSFER Zone at cab 04 shelves 01,01 RECONNECTED itself to the  (Read 1711 times)

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
The problem that occurs is "The SYSTEM FAIL TRANSFER Zone at cab 04 shelves 01, 01 RECONNECTED itself to the switch", I lose the connection with the modules and the telephones (analog and digital) are unregistered and after a while they reconnect .

Maybe someone knows how to solve this problem?


Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4100
  • Country: us
  • Karma: +133/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
The bay is losing communication with the controller or power supply is flaky.

Check Bay 4 for a loose power cable or interconnect cable/fiber, or try swapping the peripheral interface card or a different cable from the MCC to the bay.

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
Dear:
Ask me to remove the layer 2 (L2), could that be why the disconnection of the modules?

Offline ZuluAlpha

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 694
  • Country: us
  • Karma: +17/-0
    • View Profile
The Layer 2 switch config would not affect losing connecting to a peripheral cabinet. I would focus on the hardware or cabling of that particular cabinet. 

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
Dear:

Yesterday I changed the font for one of the cabinets, but it shows the same error.
Today I will try to change the controller and update the information.

A query attached a screenshot, where is the log, do you have knowledge if it is related to the Reconnecting alarm?

Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4100
  • Country: us
  • Karma: +133/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
So all the cabinets are doing this at the same time? You have an issue in the control cabinet or common control cards, not the individual peripheral cabinet. Would need to know more of the hardware and software info.
« Last Edit: August 15, 2021, 09:29:02 AM by acejavelin »

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
I have 5 cabinets, in the first instance it was only 1 cabinet today I am with the problem in 3 cabinets 2,3,4.
I need to solve the reboot problem.
I am using the following procedure to change the cards in the following order in the cabinet 3:
1) Power Source (changed)
2) Control Card
3) Fiber Optic interconnection card

With these steps can the problem be solved? or is the problem in MXe?

Thank you for your answers

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
Attached screenshots of the Logs. I hope it contributes so that you can help me solve this problem.

I am eternally grateful for all your responses.

Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4100
  • Country: us
  • Karma: +133/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
I would suspect a bad FIM module...

Backup and shutdown, open the chassis and blow out any dust/debris... unseat the FIM module and then reseat it carefully. Reassemble and put back into service. Remember to properly clean your fiber ends before reconnecting. I have seen dust/debris get into the fiber connectors on the FIM card and cause connectivity issues. If problems persist, I would suspect the FIM.

https://www.chemtronics.com/how-to-clean-and-how-not-to-clean-fiber-optic-connectors

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
Dear:
The change of FIM modules was made on Friday, there was a restart on Saturday and so far no other restart has been presented.

Can you help me with another alternative to the ones mentioned above?

Offline san_typ

  • Jr. Member
  • **
  • Posts: 47
  • Country: ec
  • Karma: +0/-0
    • View Profile
Dear:

o far the control panel has not been restarted, apparently it has already been solved.

Thanks


 

Sitemap 1 2 3 4 5 6 7 8 9 10