Author Topic: mitel E2T booting issue  (Read 1770 times)

Offline minshad

  • Contributer
  • *
  • Posts: 9
  • Country: ec
  • Karma: +0/-0
    • View Profile
mitel E2T booting issue
« on: July 20, 2019, 06:44:46 AM »
it keep booting after mistakenly changed e2t card address from UBOOT


U-Boot 2015.10 (Apr 04 2019 - 15:25:14 -0400) mxeiii 1.0.3.8

Reset Status:

CPU:   e300c1, MPC8360EA, Rev: 2.1 at 528 MHz, CSB: 264 MHz
Board: Mitel MXe-III, U-Boot 2015.10 (Apr 04 2019 - 15:25:14 -0400) mxeiii 1.0.3.8
Refresh UBOOTROM

Reset Cause (0x3 - EXTERNAL_INTERNAL_SOFT_RESET)

       Watchdog enabled
I2C:   ready
DRAM:

Configuring DDR2 SODIMM using SPD drivers
DDR
Starting POST...

SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
SDRAM CS1 Address  Walk 1................... PASSED
SDRAM CS1 Address  Walk 0................... PASSED
SDRAM CS2 Address  Walk 1................... PASSED
SDRAM CS2 Address  Walk 0................... PASSED

1 GiB (DDR2, 64-bit, ECC off, 264 MHz)
Flash: 4 MiB
PCI:   Bus Dev VenId DevId Class Int
PCI:
  00:16.0     - 1095:3512 - Mass storage controller
In:    serial
Out:   serial
Err:   serial
Found valid environment in flash.
Slot id 0

do_mitel_stuff_inram Tests...
SATA RAID Controller Detected.
Sil5923Reset - Done
Rebuild - Max transfer 6, Min transfer 0, Rebuild Inc 0
Bay 1 is disk operational.
Bay 2 is disk operational.
Net:   UEC0

do_mitel_ethstuff_inram Tests...

do_mitel_programfpga Tests...
FPGA version 0002:6123 loaded


E2T card installed; wait for 10s to let it run its preboot command...

Press <SPACE> key 3 times within 7 seconds to stop autoboot

UEC: PHY is Generic MII (143bc31)
UEC0: Full Duplex
UEC0: Speed 100BT
UEC0: Link is up
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16

Retry time exceeded; starting again
Booting VxWorks E2T image with DHCP configuration...
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16

Retry time exceeded; starting again
Could not load E2T8260...





Offline JasonTaylor

  • Full Member
  • ***
  • Posts: 122
  • Country: gb
  • Karma: +4/-0
    • View Profile
Re: mitel E2T booting issue
« Reply #1 on: August 09, 2019, 04:37:24 AM »
Looks like the E2T is broadcasting dhcp request and not getting one?  Configure DHCP options 66 and 67
66 TFTP Server, IP address format
67 Boot file, string value (always /sysro/E2T8260)


 

Sitemap 1 2 3 4 5 6 7 8 9 10