5330 Firmware Issues

[johnp]

6.3.3.6 is in Mitel load 14.0.2.26, just wondering where 6.3.3.7 is. 6.3.3.8 is the break point from what I see 6.3.3.6 appears to be in the 10.0.3.17 load

[dilkie]

 6.3.3.8 is where the web server was disabled, I don't know if  6.3.3.7 ended up in any releases (maybe MBG for some build or other).

[isisyodin]

Hi guys,

First time using Mitel  . I recently got my hands on a Mitel 5330 which has the following firmware:
Main: 05.02.02.07
Boot: 05.02.02.01
I have set it to SIP mode which I plan to use with my FreePBX system. I have failed miserably trying to get this phone to register or flash.The web interface only allows to point to a TFTP server which as far as I can tell only reboots the phone but doesn't read my cfg file.
I noticed that upon resetting to defaults, I could set SIP and enable firmware updates via TFTP. I have done both but the TFTP server address is wrong as it errors out. When the phone boots, I can get into the Admin Tools and make some changes. However, when I try to enter the IP address for my TFTP server, there is no way to add the "dot" on the IP address. When I tap twice on the * button I get *. For example, my IP address looks like 192*.168*.0*.2 Its is very strange. I have not found a way to move the cursor over. When I backspace, it deletes the character.

I am hoping someone here can share their SIP working firmware alongside some pointers on how to flash the 5330. A version that has a Web GUI would be nice but a flat cfg file version is also welcome.

Thanks

[isisyodin]

Anyone?

[johnp]

The phones I have were setup via the phone's webpage versus any config file.

[itsupportsea]

6.3.3.8 is where the web server was disabled, I don't know if  6.3.3.7 ended up in any releases (maybe MBG for some build or other).

I have the same problem. Anyone has a source for the older firmware so I can downgrade??? Please help.
itsupportsea at sailsgroup.com

[itsupportsea]

So I decided to put the older version back using Tftp running on my PC and it was back to as it was. I configured it again via the web gui and it worked again but still flipped to “No Reg” after a while.

I have the same problem and I need the older version of the firmware. Can you please post it here so I can "fix" my phones?

Thanks in advance.

-PC

[acejavelin]

So I decided to put the older version back using Tftp running on my PC and it was back to as it was. I configured it again via the web gui and it worked again but still flipped to “No Reg” after a while.

I have the same problem and I need the older version of the firmware. Can you please post it here so I can "fix" my phones?

Thanks in advance.

-PC

No offense intended here, but trying to get Mitel 53xx phones working as generic SIP devices 10 years after the firmware was discontinued seems ludicrous to me. Seriously, you can buy used Polycom sets or new Yealink sets and replace 10 old Mitel devices for much less than the cost of the time to try to get those old Mitel's working in SIP mode. A decent Yealink or Polycom refurbished phone can be had for under $40, some under $30, and will work for some time on almost any platform.

Don't get me wrong, I love the Mitel 5300 series devices, the quality is outstanding, but they are terrible SIP devices.

[dilkie]

without any warranty, YMMV, etc... you can tftp the last web server load from 66.46.196.230.

[prabbide]

without any warranty, YMMV, etc... you can tftp the last web server load from 66.46.196.230.

Is this still true?  I can't get my 5330e to pull down the firmware.

Thanks.

[dilkie]

still running, last d/l was this morning at 3am est.

[dilkie]

Ah... I don't have the 'e' version up...  let me go look.

Okay... looks like I can use 6.5.0.9 as the pre-deleted-web-server and that build has loads for all the sets..

try again.

[prabbide]

Thank you very much!  It worked.

[prabbide]

Would it be possible for me to download all the files in that load so i can put them on my own tftp server?  I'm not sure what files to pull down.
Thanks.

[dilkie]

Would it be possible for me to download all the files in that load so i can put them on my own tftp server?  I'm not sure what files to pull down.
Thanks.

BluetoothCordlessModule.bin  L2Boot53xxTtn8M.bin  Recovery5505Ttn.bin       sip5324ttntone_GB.bin     sip5340ttnlang_nl_NL.bin
BootIp5324Ttn.bin            MainIp5320.bin       sip5324ttnlang_de_DE.bin  sip5324ttntone_MX.bin     sip5340ttntone_AU.bin
BootIp5340.bin               MainIp5324Ttn.bin    sip5324ttnlang_en_US.bin  sip5324ttntone_NL.bin     sip5340ttntone_DE.bin
BootIp5360.bin               MainIp5340.bin       sip5324ttnlang_es_ES.bin  sip5324ttntone_NZ.bin     sip5340ttntone_FR.bin
BootIp5540.bin               MainIp5340e.bin      sip5324ttnlang_fr_FR.bin  sip5324ttntone_US.bin     sip5340ttntone_GB.bin
CHNcharUnEnc.bin             MainIp5360.bin       sip5324ttnlang_nl_NL.bin  sip5340ttnlang_de_DE.bin  sip5340ttntone_MX.bin
FirmwareVersion.txt          MainIp5505Ttn.bin    sip5324ttntone_AU.bin     sip5340ttnlang_en_US.bin  sip5340ttntone_NL.bin
L2Boot5360Ttn32M.bin         MainIp5540.bin       sip5324ttntone_DE.bin     sip5340ttnlang_es_ES.bin  sip5340ttntone_NZ.bin
L2Boot53xxeTtn8M.bin         Recovery5340e.bin    sip5324ttntone_FR.bin     sip5340ttnlang_fr_FR.bin  sip5340ttntone_US.bin