Author Topic: How to Block Incoming Calls Based on Caller ID - Mitel 3300  (Read 43022 times)

Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
I'm finally releasing this.

We've always been told this couldn't be done but I've found that one of the features of the 3300 can allow us to do it.

So here's the doc.
How to stop specific callers from being able to dial in.
You can download the PDF here

Please use this forum for comments and to ask question.   I cannot answer PM questions.

Some notes:
1) It's complex.  If  you're not an experienced tech then you may want to enlist the help of more senior individuals. 
2) Don't try to program it during busy hours.  If you make a mistake it will cause all calls to fail.  Do it during a slow time to give you time to test & debug.
3) This only works for SIP trunks and Euro ISDN.
4) This may cause Anonymous calls to fail.   So far I haven't found a way around this.   Please let me know if you do.

Ralph

If you find this useful, then please consider making a donation to the website to help keep the lights on.   Donate
(The donation page does say "University Music On Hold" - that is a sister site.)


« Last Edit: August 03, 2018, 10:32:08 PM by ralph »


Offline PC77375

  • Full Member
  • ***
  • Posts: 189
  • Country: us
  • Karma: +6/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #1 on: May 01, 2015, 09:16:23 AM »
Bravo Ralph! This will change the world as we know it. What about processing load though? Have you found that this affects cp performance at all?

Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #2 on: May 01, 2015, 09:50:28 AM »
Processing load has not been checked.
In my lab I do not have a way of checking under load so if you do please let us know what you see.

Ralph

*** UPDATE May-1-15  ****

Mitel reviewed the doc.
Here's the comments they sent me:


----  <SNIP> --------
Hi Ralph, looks pretty good. Note step 3 references IP/XNET Trunk Group 10, not 1.
On the performance side, remember that this *triples* traffic for this particular type of call.

If all calls are to be looped back, you will have
i) the original inbound call
ii) the outbound loopback call
iii) the inbound loopback call.
There will also be increased use of call processing for ARS to insert and remove digits.
You will need to be cautious in its use on a busy site. The Engineering tool may be useful to indicate a higher traffic level when designing the system.
All told, great idea!

----  <End SNIP> --------
« Last Edit: May 01, 2015, 04:54:35 PM by ralph »

Offline moona

  • Jr. Member
  • **
  • Posts: 56
  • Country: nz
  • Karma: +0/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #3 on: May 25, 2015, 06:50:46 PM »
Just a question from someone still quite new to Mitel, this can be done in 2min on an Asterisk based system. Why is it so difficult for Mitel to implement something like this? Well done on figuring out a method though  :)

Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #4 on: May 26, 2015, 08:31:03 AM »
Dang good question.
We've all been asking for this for something like forever.
It would also seem to me that the Mitel DEV team could solve this easily.
All they'd have to do now is implement source based routing.
If they took their existing Inward Dialing Modification and allowed us to map destination based off of that then it could be easily done.

Ralph


Offline mszodiac

  • Sr. Member
  • ****
  • Posts: 232
  • Country: ca
  • Karma: +7/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #5 on: November 05, 2015, 02:49:08 PM »
Thanks for this ralph.  So why won't this work on T1s?

Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #6 on: November 05, 2015, 04:04:24 PM »
Because it relies on modifying the CLID via the Calling Party Inward Dialing Modification form.
That doesn't work on PRIs.  (I don't remember but it might work on Euro ISDN)

Ralph

Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2176
  • Country: us
  • Karma: +66/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #7 on: November 05, 2015, 07:24:18 PM »
I think it works on the Euro PRI

Offline PC77375

  • Full Member
  • ***
  • Posts: 189
  • Country: us
  • Karma: +6/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #8 on: June 15, 2016, 11:59:30 AM »
There is always this as an option, if cost is not a concern.

http://www.securelogix.com/

Just for grins, about 30% of our calls over a 90 day period are blocked as they are harrasing or phishing calls. We have also been able to stop TDOS attacks on our PBX using this product. It is essentially a Tbird sitting between the Telco and the PBX, analyzes and processes calls based on rules before they hit the PBX. If anyone has any questions about it or would like to see it in action, let me know. We currently have these installed at 4 of our locations.

Offline warlockcode

  • New Member
  • *
  • Posts: 3
  • Country: au
  • Karma: +0/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #9 on: May 24, 2017, 08:20:04 PM »
Hi Ralph

Care to share that doc again, link does not seem to work

Thanks.

Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #10 on: May 25, 2017, 07:36:23 AM »
Unfortunately I no longer have the doc.
I had it dropbox.  They made a change and I lost everything that was on it that I didn't have anywhere else.

If someone else has it, please upload it.

Ralph

Offline sarond

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1381
  • Country: au
  • Karma: +71/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #11 on: August 09, 2017, 01:39:24 AM »
Apparently there is going to be a blacklist option in MiVB 9.
For those that have access to MUG.
https://mitelusergroup.org/forums/topic/block-incoming-did-numbers-on-3300/#post-2937


Online ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #12 on: August 14, 2017, 10:57:46 PM »
Outstanding!  Bout time.

Ralph

Offline pmhaynes

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 237
  • Country: gb
  • Karma: +11/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #13 on: January 31, 2018, 04:05:03 AM »

Offline irongladiator

  • Global Moderator
  • Sr. Member
  • *****
  • Posts: 346
  • Country: us
  • Karma: +12/-0
    • View Profile
Re: How to Block Incoming Calls Based on Caller ID - Mitel 3300
« Reply #14 on: July 10, 2018, 05:49:06 PM »
Hey all,
Attached is a copy of Ralph's guide.

Thanks Ralph!

-Iron


 

Sitemap 1 2 3 4 5 6 7 8 9 10