Author Topic: Minor Alarm  (Read 15866 times)

Offline ttrumble111

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #15 on: February 07, 2012, 03:18:11 PM »
Ralph,

I get the plid 6-1-1-6 would be "Cabinet 6 - Shelf 1 - Slot 1 - Circuit 6", and I can physically see it, but what about the others "cabinets 1, 4, & 7" or "shelfs 3 & 1" or "Slots 32, 10, 11, 6, & 2" - whats that all about?

1             3         32     ViperAA IP     Controller
1             1         10     MCSTHA         ICP Comms
1             1         11     MC266AA       Communications Processor
4             1          6      MCASUAA       ASU
7             1          2      MC270A         Universal T1

I pieced together the information above from the log when I rebooted the 3300 last Friday. I am just trying to better understand the layout of the 3300 better so if something fails or is in an alarm state I can better troubleshoot it.

One other question. I know I can plug and unplug the Ethernet Port, FIM TX & RX, and the T1 connectors while its running without adversely affecting the 3300 - I think??? PLEASE tell me if I am wrong so that I don't fry the 3300, but what about the RJ21/Amphenol/50 Pin telco connector on the back? Can I unplug and plug the Amphenol connector while its running without hosing the 3300?

- Tom


Offline v2win

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 628
  • Country: us
  • Karma: +11/-0
    • View Profile
Re: Minor Alarm
« Reply #16 on: February 07, 2012, 03:54:11 PM »
Cabinet 1 is the 3300 itself the cards in cabinet 1 are virtual. Cabinet 4 is your embedded ASU and Cabinet 7 is your T1 module.

Yes you can unplug all the connections including the 50 pin amp cable without hurting anything. You will lose service on those but that is implied.

Offline ttrumble111

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #17 on: February 09, 2012, 03:54:06 PM »
Thanks go to Ralph & v2win.

My backup Mitel system cutover went great Tuesday night @ 10PM.

Your answers to my questions have greatly assisted me on this project and I thank you.

Beers all around! ;D

- Tom

Offline ttrumble111

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #18 on: February 09, 2012, 04:15:17 PM »
Oops I forgot to ask.

When Ralph suggested 'set thres lines 9 20 100' I did that but on a subsequent reboot it went back to "0 20 100". How do you save that threshold config to the firmware or configuration file so that on the next reboot I don't have to reset it again.

- Tom

Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: Minor Alarm
« Reply #19 on: February 09, 2012, 04:31:08 PM »
That should have stayed.   That command is supposed to survive a reboot.

Not sure what's happening here.

Ralph

Offline MitelMania

  • Jr. Member
  • **
  • Posts: 50
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #20 on: February 09, 2012, 09:10:43 PM »
if you did a database restore the thresholds are lost..  I saw something about a backup and what not in the thread..  if you upgraded or did any kind of DB restore it will erase the alarm thresholds set by the set thresh commands..
-Christopher

Offline ttrumble111

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #21 on: February 13, 2012, 09:50:05 AM »
Thank you Christopher,

During the March Reboot of my 3300 backup, that is currently in production, I will check the threshold and see if it goes back to the default.

- Tom

Offline ttrumble111

  • Contributer
  • *
  • Posts: 12
  • Karma: +0/-0
    • View Profile
Re: Minor Alarm
« Reply #22 on: March 05, 2012, 10:21:50 AM »
Before I reboot my "Backup" 3300, thanks to Ralph, Christopher, & v2win, from the Shell and check that the "thres lines 9 20 100" remained I would like to ask a couple of questions:

  • Can I issue a command from the ESM similar to the appShutdown from the Shell and then <SPACE><SPACE><SPACE> for a simple reboot?
  • I have been rebooting the Mitel 3300 once a month manually with the "appShutdown" command for the past 4 months and it seems that the reboots have kept the system running better than ever. Is this a good practice to continue? If so, what would be the command to schedule it for 0300 hours on the 1st of every month so that I don't have to babysit?

- Tom

Offline ralph

  • Mitel Forums Admin
  • Hero Member
  • *****
  • Posts: 5739
  • Country: us
  • Karma: +468/-0
  • Published Author: http://amzn.to/2dcYSY5
    • View Profile
Re: Minor Alarm
« Reply #23 on: March 05, 2012, 12:57:57 PM »
I generally set up to reboot weekly so my command I use is "Program Reboot Sched Friday 2:15"

The following is right from the help files:


PROGRAMMED REBOOT
Qualifiers:
COURTESY ON

COURTESY OFF

DISPLAY

RESOURCE RECOVERY ON

RESOURCE RECOVERY OFF

RESOURCE RECOVERY <hh:mm:ss>

SCHEDULE ON

SCHEDULE OFF

SCHEDULE DAILY <hh:mm:ss>

SCHEDULE <day-of-week> <hh:mm:ss>

SCHEDULE MONTHLY <week # [1-4]> <day-of-week> <hh:mm:ss>

SCHEDULE INTERVAL <interval in weeks [1-52]> <MMM> <day-of-month> <hh:mm:ss>

•Note: The default values are:
PROGRAMMED REBOOT SCHEDULE IS OFF
PROGRAMMED REBOOT SCHEDULED: DAILY 02:15:00
PROGRAMMED REBOOT RESOURCE RECOVERY IS ON
PROGRAMMED REBOOT RESOURCE: RECOVERY 02:15:00
PROGRAMMED REBOOT COURTESY IS OFF 




 

Sitemap 1 2 3 4 5 6 7 8 9 10