Home Page Articles User Guides News Letter  



Author Topic: AWV configuration  (Read 344 times)

Offline sunspark

  • Sr. Member
  • ****
  • Posts: 273
  • Country: ma
  • Karma: +3/-0
    • View Profile
AWV configuration
« on: November 15, 2017, 05:38:33 AM »
Hi ,

I have a micollab 7.3 in lan mode with a MBG in  Dmz

Micollab: lan address 192.168.1.1

Mbg.mycompagny.com / public address: x.x.x.58

conf.mycompagny.com / public address: x.x.x.59


I look at the engenieering guideline, but I do not understand how I have to redirect AWC in the firewall

Ps: I'm in version 7.2 so I have to use two external addresses.

Any help will be appreciated.


Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1204
  • Country: us
  • Karma: +13/-0
    • View Profile
Re: AWV configuration
« Reply #1 on: November 15, 2017, 07:48:11 PM »
You may want to upgrade to latest so that you can use a single external ip. Firewall rule as I think for the second address is inbound 443 converts to 4443, hits the web proxy and get sent to AWV. Reverse rule for outbound.

I think the new single name and just allowing 4443 internal and external makes for an easier install and if having to deal with firewall vendors less of a hassle.

Offline sunspark

  • Sr. Member
  • ****
  • Posts: 273
  • Country: ma
  • Karma: +3/-0
    • View Profile
Re: AWV configuration
« Reply #2 on: November 16, 2017, 03:56:48 AM »
Actually , i dont have swa , so i'm not able to upgrade.

Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2644
  • Country: us
  • Karma: +62/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
Re: AWV configuration
« Reply #3 on: November 16, 2017, 08:10:47 AM »
Easiest way to see what ports you need open is use the Teleworker Network Analyzer, run it locally and see what ports are open on the server, those need to be forwarded in the firewall.

As far as second IP, I've always struggled with that one... Usually open all the AWV/Conference/Collaboration ports and it works.

Sent from my Moto G (5) Plus using Tapatalk


Offline sunspark

  • Sr. Member
  • ****
  • Posts: 273
  • Country: ma
  • Karma: +3/-0
    • View Profile
Re: AWV configuration
« Reply #4 on: December 11, 2017, 04:13:03 PM »
Easiest way to see what ports you need open is use the Teleworker Network Analyzer, run it locally and see what ports are open on the server, those need to be forwarded in the firewall.

As far as second IP, I've always struggled with that one... Usually open all the AWV/Conference/Collaboration ports and it works.

Sent from my Moto G (5) Plus using Tapatalk

Hi Ace ,

I just want to know , if i need a special public address on each MBG (in dmz mode) for awc ? 
cheers

Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1204
  • Country: us
  • Karma: +13/-0
    • View Profile
Re: AWV configuration
« Reply #5 on: December 11, 2017, 07:33:16 PM »
You could also change the internal and external address on AWV to the same 4443 and forward 4443 from outside address used by MAS to it's internal address. I don't know your dmz setup. This would bypass proxy for connectpoint traffic

Offline sunspark

  • Sr. Member
  • ****
  • Posts: 273
  • Country: ma
  • Karma: +3/-0
    • View Profile
Re: AWV configuration
« Reply #6 on: December 12, 2017, 07:41:27 AM »
You could also change the internal and external address on AWV to the same 4443 and forward 4443 from outside address used by MAS to it's internal address. I don't know your dmz setup. This would bypass proxy for connectpoint traffic

Ok but if i want tu use a specific address for awc? I have tu use wan interface for dmz?

Offline johnp

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1204
  • Country: us
  • Karma: +13/-0
    • View Profile
Re: AWV configuration
« Reply #7 on: December 12, 2017, 08:48:09 PM »
The second ip only comes into play with the client connection i.e. connectpoint. Web access can follow the proxy. The way the join via client works is it ask for a connect using the programmed values in AWC, how you connect to make a meeting creates the web URL's

Offline billbry66

  • Jr. Member
  • **
  • Posts: 30
  • Karma: +1/-0
    • View Profile
Re: AWV configuration
« Reply #8 on: December 18, 2017, 06:32:49 AM »
do this

PUB1 with name conf.company.com --- natted to MBG internal address
PUB2 with name confclient.company.com ---natted to internal MBG address

on MBG setup as local dns and set entry for both names to the internal address of the Micollab

setup webproxy on the MBG to handle these names

open TCP ports 443 80 5060,5061 6801,6802 3998 6881 36008 37000

and UDP ports 5060 69 20000-35999

PUB1 is used for TW handsets

name1 is used for awv access and micollab client access
name 2 is used in the background for the AWV client - has to be set in AWV blade




 

Sitemap 1 2 3 4 5 6 7 8 9