Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - johnp

Pages: [1] 2 3 ... 141
1
Mitel MiVoice Business/MCD/3300 / Re: MItel 3300 integration to carrier 14 ip Ivr
« on: April 21, 2024, 05:02:34 PM »
Like Ace says, you would have to be able to send out unique caller id values per room. I don't know why you want to send rooms to this in the first place. I might set up some zones and location based dialing to send 0 either out to this or not.

2
Mitel Software Applications / Re: Nupoint
« on: April 16, 2024, 04:51:32 PM »
There is a knowledge base article on this

3
Mitel MiVoice Business/MCD/3300 / Re: MITEL 5634 WIFI HANDSET - TELEWORKER Configuration
« on: April 12, 2024, 02:34:32 PM »
FWIW, when you crete this, the sip password s an internal value. When adding teleworker, it creates this such that there is a different external name and a complex unknown password.

You can modify the sip teleworker external name and password so that it is the same. If so, I would make sure the internal is not simple.

You have to get into the MBG to make the changeses.

4
Mitel SX200, SX2000, and older SX platforms / MOVED: Unable to receive or make outside calls. Sys Alarm #114 on controller.
« on: April 12, 2024, 11:37:57 AM »
This topic has been moved to MiVoice Office 250/Mitel 5000.

This is a 250 question

5
Mitel MiVoice Business/MCD/3300 / Re: Teleworker problem with calling in-office IP desk phones
« on: April 11, 2024, 06:12:43 PM »
FWIW, the audio internally is udp in the 50000 range, but teleworker to remote set goes in the 20000.

6
Mitel MiVoice Business/MCD/3300 / Re: Teleworker problem with calling in-office IP desk phones
« on: April 11, 2024, 06:10:32 PM »
Yes that is how the audio has always been done on the 3300, I think the 250 stays in the middle

7
Mitel MiVoice Business/MCD/3300 / Re: Teleworker problem with calling in-office IP desk phones
« on: April 11, 2024, 04:38:37 PM »
The 3300 only sets up and tears down the calls, all audio streams from device-device, or perhaps device-teleworker server in your case

8
Mitel MiVoice Business/MCD/3300 / Re: Mitel MCD - Unable to Clear CESID Alarm
« on: February 19, 2024, 04:11:20 PM »
The automatic update is a crap shut, if they replace switches all hell breaks loose. Think it is better managed via station or base station.

9
Mitel Software Applications / Re: NuPoint Call Directory Call Flow Reports - Automated
« on: January 19, 2024, 05:29:23 PM »
Check this out https://wiki.koozali.org/Cron_entry This tells how to make changes survive upgrades. This is based on Mitel Linux i.e e-smith

10
SIP On Mitel / Re: 5330 Firmware Issues
« on: January 11, 2024, 06:49:44 PM »
https://drive.google.com/drive/folders/1H1Im6Qp7DsJNAYY2TQ8IrL99tI2iXSTj?usp=sharing

11
Mitel Software Applications / Re: Recreate Deleted Mailbox for new MiCollab User
« on: January 11, 2024, 06:47:05 PM »
Would need to see under detained users why this fails

12
Mitel Software Applications / Re: NuPoint Call Directory Call Flow Reports - Automated
« on: January 11, 2024, 06:42:38 PM »
From what I know this file will be recreated upon the next call, so deleting should not be an issue IMHO

13
Mitel Software Applications / Re: NuPoint Call Directory Call Flow Reports - Automated
« on: January 10, 2024, 05:37:40 PM »
Not sure about getting the report emailed, but in theory you could use chown to run a delete file for the stats at midnight and when another call comes in, the file I believe is recreated. These are in /usr/vm/val5/CallFlows/xxxx_yyyy_stats.xml where xxxx... represents the flow desired. It might also make sense to use this file instead of the report. One could at 11:59 have an automated download of it via a sftp client, just prior to reset.

14
Mitel MiVoice Business/MCD/3300 / Re: MXe-III Software load 10.0.2.23 Release level 6.0 SP 2 - Forward all calls
« on: November 27, 2023, 04:45:10 PM »
If using DID table and trunks can you internal to external, you could change the destination for the numbers to either a speedcall or the full number including dialout digit

15
Mitel Software Applications / Re: Mitel Soft Client
« on: November 26, 2023, 04:05:10 PM »
Just was testing on a new site using phonerlite and tls, connected without issue, where as udp 5060 looks to be restricted by the data vendor there. Did get 5060 tcp to connect but had issues also possibly a firewall thing.

Pages: [1] 2 3 ... 141