Author Topic: SSD PATA in MXe II or CX controllers?  (Read 1665 times)

Offline petr.necas

  • Sr. Member
  • ****
  • Posts: 393
  • Country: cz
  • Karma: +8/-0
    • View Profile
SSD PATA in MXe II or CX controllers?
« on: December 29, 2016, 07:24:06 AM »
As I know SSD drives are not supported in the old MXe II or CX controllers, but do anybody have any experience with SSD PATA drives (e.g. Transcend SSD330 - 32GB TS32GPSD330) in these controllers? I know Mitel support will then not provide any support, but it will be on our risk.


Offline billbry66

  • Jr. Member
  • **
  • Posts: 87
  • Karma: +3/-0
    • View Profile
Re: SSD PATA in MXe II or CX controllers?
« Reply #1 on: January 01, 2017, 03:58:40 AM »
if your not worried about lack of support then i cant see it being a problem

give it a go , use the tech handbook motcc method with a FixPartition option
- this should format the drive and create the appropriate partitions

if the controller boots then should be good to go

Offline Ronan

  • Full Member
  • ***
  • Posts: 149
  • Country: fr
  • Karma: +1/-0
    • View Profile
Re: SSD PATA in MXe II or CX controllers?
« Reply #2 on: January 04, 2017, 03:00:57 AM »
It can't be worse than 10 years old PATA DD. I've just spent 4 hours replacing one in an MXe, most of that time lost because the thing is slow as hell.

Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4064
  • Country: us
  • Karma: +129/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
Re: SSD PATA in MXe II or CX controllers?
« Reply #3 on: January 04, 2017, 09:00:51 AM »
I have used lots of "off-the-shelf" drives in older 3300 controllers, never had an issue, as mentioned before just make sure to use the FixPartition flag when installing the software (follow guide in Tech Handbook). I don't see any reason that this wouldn't work as long as the controller recognizes the drive and boots, which shouldn't be an issue since most of those PATA/SSD drives emulate a normal IDE hard drive to the BIOS.

Offline petr.necas

  • Sr. Member
  • ****
  • Posts: 393
  • Country: cz
  • Karma: +8/-0
    • View Profile
Re: SSD PATA in MXe II or CX controllers?
« Reply #4 on: January 05, 2017, 02:49:32 AM »
The SW gets lower and slower, I was surprised how fast was the old ICP 8.0 installed on CX with HDD compared to the latest MCD 8.0. I will order the SSD and do some measurements....

Offline petr.necas

  • Sr. Member
  • ****
  • Posts: 393
  • Country: cz
  • Karma: +8/-0
    • View Profile
Re: SSD PATA in MXe II or CX controllers?
« Reply #5 on: January 11, 2017, 03:20:54 AM »
I tested the Transcend SSD330 - 32GB TS32GPSD330 inside our lab CX controller, the drive worked well, however there was not any performace increase compared to the original Hitachi 80GB hardrive :-(.

Here are my results:

                                                     HDD                  SSD
manual software installation:           37 min               39 min
database restore:                           34 min               33 min
database backup:                           4:53 min            4:43 min
restart (RESET SYSTEM command)   17 min 43 sec    17 min 30 secs
DBMS CHECK FULL                          5 min 50 sec      5 min 40 secs

Offline acejavelin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4064
  • Country: us
  • Karma: +129/-0
  • High-tech, heavy metal redneck!
    • View Profile
    • Like what I do and wanna help out? Send me a donation!
Re: SSD PATA in MXe II or CX controllers?
« Reply #6 on: January 11, 2017, 06:19:17 PM »
Interesting and unexpected. Guess that means the hard drive is clearly not the bottleneck in the speed of these things. :/

Then again, I am trying to think about the few SSD MXeIII's I have done... I don't recall them being any faster than the standard HDD models either, but I never really thought about it until now.


 

Sitemap 1 2 3 4 5 6 7 8 9 10